Retains Reverse Plug & Spring On Guide Rod During Field Stripping
Handy steel clip slips over a full-length guide rod and securely retains the reverse plug and spring when field stripping a 1911. Acts like a “third hand” to keep the spring and plug on the rod while you remove or install the slide. Eliminates the need for improvised tools like small nails or paper clips that can fall out and cause a safety hazard by unexpectedly launching the spring, plug, or rod across the shop.
SPECS: Steel, approx. 21⁄8" (5.4cm) long.
Más...
Retiene el Tapón Inverso y el Resorte en la Varilla Guía Durante el Desmontaje en el Campo
El práctico clip de acero se desliza sobre una guía de varilla de longitud completa y retiene de forma segura el tapón inverso y el resorte al desmontar una 1911 en el campo. Actúa como una "tercera mano" para mantener el resorte y el tapón en la varilla mientras quitas o instalas la corredera. Elimina la necesidad de herramientas improvisadas como clavos pequeños o clips de papel que pueden caerse y causar un peligro de seguridad al lanzar inesperadamente el resorte, el tapón o la varilla por el taller.
ESPECIFICACIONES: Acero, aproximadamente 21⁄8" (5.4cm) de largo.
Más...
Evaluaciones de clientes para COMPETITIVE EDGE DYNAMICS REVERSE PLUG RETENTION CLIP
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3,5
Works well, though I have so many small hex wenches and small diameter wire accumulated on my bench over the past 32 years. Bought this out of interest alone and it is well designed and seems strong so I can't say anything negative for a simple tool.
Reverse Plug Retention Clip - Review(21/07/2016)
I bought this because cleaning my Wilson Combat Officer's model 1911 with a Reverse slide plug was a pain - the 'homemade pin' kept falling out. This part is a good concept, but required modification to work. 1st: the 'short' clip was still too long for an Officer's model I cut it and then re bent the end to work. 2nd: the original 'bend' length was way too short to function - at all. 3rd. The 'circle' diameter was too large for the slide rod. I bent it to a closer match. Once these 'mods' were done, the clip works well. It might work better on a Commander or full size 1911; but I strongly suspect the 'pin end' will need to be re bent for a longer length.
N.º de producto: 100004616 COMPETITIVE EDGE DYNAMICS REVERSE PLUG RETENTION CLIP Ref Fabricante: 300033 El práctico clip de acero se desliza sobre una guía de varilla de longitud completa y retiene de forma segura el tapón inverso y el resorte al desmontar una 1911 en el campo. Actúa como una "tercera mano" para mantener el resorte y el tapón en la varilla mientras quitas o instalas la corredera. Elimina la necesidad de herramientas improvisadas como clavos pequeños o clips de papel que pueden caerse y causar un peligro de seguridad al lanzar inesperadamente el resorte, el tapón o la varilla por el taller.
16.9EUR516,90 €
*
Plazo de entrega de aproximadamente 14-21 días. 5 pcs. en el almacén de EE.UU.
Retains Reverse Plug & Spring On Guide Rod During Field Stripping
Handy steel clip slips over a full-length guide rod and securely retains the reverse plug and spring when field stripping a 1911. Acts like a “third hand” to keep the spring and plug on the rod while you remove or install the slide. Eliminates the need for improvised tools like small nails or paper clips that can fall out and cause a safety hazard by unexpectedly launching the spring, plug, or rod across the shop.
SPECS: Steel, approx. 21⁄8" (5.4cm) long.
Más...
Retiene el Tapón Inverso y el Resorte en la Varilla Guía Durante el Desmontaje en el Campo
El práctico clip de acero se desliza sobre una guía de varilla de longitud completa y retiene de forma segura el tapón inverso y el resorte al desmontar una 1911 en el campo. Actúa como una "tercera mano" para mantener el resorte y el tapón en la varilla mientras quitas o instalas la corredera. Elimina la necesidad de herramientas improvisadas como clavos pequeños o clips de papel que pueden caerse y causar un peligro de seguridad al lanzar inesperadamente el resorte, el tapón o la varilla por el taller.
ESPECIFICACIONES: Acero, aproximadamente 21⁄8" (5.4cm) de largo.
Más...
Evaluaciones de clientes para COMPETITIVE EDGE DYNAMICS REVERSE PLUG RETENTION CLIP
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3,5
Works well, though I have so many small hex wenches and small diameter wire accumulated on my bench over the past 32 years. Bought this out of interest alone and it is well designed and seems strong so I can't say anything negative for a simple tool.
Reverse Plug Retention Clip - Review(21/07/2016)
I bought this because cleaning my Wilson Combat Officer's model 1911 with a Reverse slide plug was a pain - the 'homemade pin' kept falling out. This part is a good concept, but required modification to work. 1st: the 'short' clip was still too long for an Officer's model I cut it and then re bent the end to work. 2nd: the original 'bend' length was way too short to function - at all. 3rd. The 'circle' diameter was too large for the slide rod. I bent it to a closer match. Once these 'mods' were done, the clip works well. It might work better on a Commander or full size 1911; but I strongly suspect the 'pin end' will need to be re bent for a longer length.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.