No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Más...
Torno no necesario, No hace falta quitar barril de marco
Súper suave ángulo como actualmente utilizado por Ruger en sus armas DA 38/357. Si un retroceso un barril Ruger o sólo quiere duplicar este ángulo en cualquier otro barril, utilice este cortador. No puede usar cortadores de 18° o 11° en una garganta de 5° sin exceder el diámetro máximo de garganta o haciendo un ángulo compuesto.
Más...
Evaluaciones de clientes para BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 1
My 45 cal, 5 Degree Did Not Cut.(15/05/2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16/11/2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.
N.º de producto: 080486500 BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER Súper suave ángulo como actualmente utilizado por Ruger en sus armas DA 38/357. Si un retroceso un barril Ruger o sólo quiere duplicar este ángulo en cualquier otro barril, utilice este cortador. No puede usar cortadores de 18° o 11° en una garganta de 5° sin exceder el diámetro máximo de garganta o haciendo un ángulo compuesto.
69.9EUR869,90 €
*
Plazo de entrega de aproximadamente 14-21 días. 8 pcs. en el almacén de EE.UU.
N.º de producto: 080486100 BROWNELLS 5 CHAMFER CUTTER FOR .38 CALIBER Súper suave ángulo como actualmente utilizado por Ruger en sus armas DA 38/357. Si un retroceso un barril Ruger o sólo quiere duplicar este ángulo en cualquier otro barril, utilice este cortador. No puede usar cortadores de 18° o 11° en una garganta de 5° sin exceder el diámetro máximo de garganta o haciendo un ángulo compuesto.
64.9EUR064,90 €
*
Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.
No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Más...
Torno no necesario, No hace falta quitar barril de marco
Súper suave ángulo como actualmente utilizado por Ruger en sus armas DA 38/357. Si un retroceso un barril Ruger o sólo quiere duplicar este ángulo en cualquier otro barril, utilice este cortador. No puede usar cortadores de 18° o 11° en una garganta de 5° sin exceder el diámetro máximo de garganta o haciendo un ángulo compuesto.
Más...
Evaluaciones de clientes para BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 1
My 45 cal, 5 Degree Did Not Cut.(15/05/2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16/11/2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.