Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Más...
La Presión del Resorte Mantiene en su Lugar las Rampas/Bases Delanteras o Traseras - Perfecto También para las Miras de .45; Diseño Totalmente Ajustable y Versátil; Excelente Espacio para el Soplete
Soluciona el problema de "la rampa se desliza justo cuando el soldador se derrite" con un émbolo puntiagudo y cargado por resorte que mantiene presión constante sobre la rampa o una mira de .45, incluso cuando el soldador fluye. Se ajusta en altura, ángulo y cantidad de presión del resorte. La base "V" no dañina centra el cañón bajo el émbolo. También mantiene en su lugar las bases de las miras traseras. Excelente espacio para el soplete.
ESPECIFICACIONES: Base de aluminio de 2" (5.1cm) de largo. Altura total de 4" (10.2cm). Brazo superior de 1-3/8" (3.5cm) de largo. Soporte del émbolo de 2" (5.1cm) de largo, conjunto del émbolo de 3" (7.6cm) de largo.
Más...
Evaluaciones de clientes para BROWNELLS RAMP SOLDERING JIG
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3,5
Love this Jig(21/05/2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31/07/2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.
N.º de producto: 080739000 BROWNELLS RAMP SOLDERING JIG050806104372 Soluciona el problema de "la rampa se desliza justo cuando el soldador se derrite" con un émbolo puntiagudo y cargado por resorte que mantiene presión constante sobre la rampa o una mira de .45, incluso cuando el soldador fluye. Se ajusta en altura, ángulo y cantidad de presión del resorte. La base "V" no dañina centra el cañón bajo el émbolo. También mantiene en su lugar las bases de las miras traseras. Excelente espacio para el soplete.
134.9EUR2134,90 €
*
Plazo de entrega de aproximadamente 14-21 días. 2 pcs. en el almacén de EE.UU.
Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Más...
La Presión del Resorte Mantiene en su Lugar las Rampas/Bases Delanteras o Traseras - Perfecto También para las Miras de .45; Diseño Totalmente Ajustable y Versátil; Excelente Espacio para el Soplete
Soluciona el problema de "la rampa se desliza justo cuando el soldador se derrite" con un émbolo puntiagudo y cargado por resorte que mantiene presión constante sobre la rampa o una mira de .45, incluso cuando el soldador fluye. Se ajusta en altura, ángulo y cantidad de presión del resorte. La base "V" no dañina centra el cañón bajo el émbolo. También mantiene en su lugar las bases de las miras traseras. Excelente espacio para el soplete.
ESPECIFICACIONES: Base de aluminio de 2" (5.1cm) de largo. Altura total de 4" (10.2cm). Brazo superior de 1-3/8" (3.5cm) de largo. Soporte del émbolo de 2" (5.1cm) de largo, conjunto del émbolo de 3" (7.6cm) de largo.
Más...
Evaluaciones de clientes para BROWNELLS RAMP SOLDERING JIG
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3,5
Love this Jig(21/05/2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31/07/2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.