Pre-machined aluminum pillars solve the difficult problem of bedding Ruger bolt action centerfire rifles. The front pillar is cut to match the 60 degree angle of the receiver screw; pre-notched with the correct contour and angles to fit against the bottom of the recoil lug and set square with the floorplate hinge. Fits all Ruger® 77 and M77® Mark II™ rifles except VT target models.
Pilares de aluminio mecanizado previamente resolver el difícil problema de Ruger rifles de cerrojo centerfire del lecho. El pilar delantero se corta para que coincida con el ángulo de 60 grados el tornillo del receptor; previamente recortados con el contorno correcto y ángulos de ajuste contra la parte inferior de la zapata de retroceso y la escuadra con la bisagra de la base de apoyo. Se adapta a todos los rifles Ruger ® 77 y M77 Mark II ™ excepto modelos blanco VT.
Evaluaciones de clientes para BROWNELLS RUGER 77/M7 MARK II BEDDING PILLARS
Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 3
Front pillar needs some work(29/03/2012)
The rear pillar was just fine. The front pillar when placed properly on the recoil lug was too far forward casuing the action screw to touch the rear inide of the pillar, and would not align properly within the stock. Solution: Center the front pillar which also aligns it properly in the stock, then fill in the gap between the pillar and the rear of the recoil lug with bedding materail. Both pillars were intentionally long and required 30-40 thousands of shortening.
Incorrectly manufactured(03/04/2012)
The notch in the front pillar is too far back leaving a gap between the rear of the recoil lug and the pillar.
Very satisfied!(28/02/2013)
I have read the other reviews and haven't had those problems, I think these work exceptionally well.
Not close(09/06/2014)
Front pillar was way short, by at least 1/4" and narrow. I used them on the M77 in the past so I don't know why they changed. Ended up making my own.
Worked very well for me(18/04/2017)
These pillars fit perfectly in my early 70's vintage M77 and improved accuracy dramatically, as noted by the four mulies killed, one shot each, from 100 to 320 yards last fall. Check fit for length and recoil lug angle match prior to installing and you should be fine. I'm buying three more sets for my other 77's.
N.º de producto: 080000007 BROWNELLS RUGER 77/M7 MARK II BEDDING PILLARS050806102262 Pilares de aluminio mecanizado previamente resolver el difícil problema de Ruger rifles de cerrojo centerfire del lecho. El pilar delantero se corta para que coincida con el ángulo de 60 grados el tornillo del receptor; previamente recortados con el contorno correcto y ángulos de ajuste contra la parte inferior de la zapata de retroceso y la escuadra con la bisagra de la base de apoyo. Se adapta a todos los rifles Ruger ® 77 y M77 Mark II ™ excepto modelos blanco VT.
Pre-machined aluminum pillars solve the difficult problem of bedding Ruger bolt action centerfire rifles. The front pillar is cut to match the 60 degree angle of the receiver screw; pre-notched with the correct contour and angles to fit against the bottom of the recoil lug and set square with the floorplate hinge. Fits all Ruger® 77 and M77® Mark II™ rifles except VT target models.
Pilares de aluminio mecanizado previamente resolver el difícil problema de Ruger rifles de cerrojo centerfire del lecho. El pilar delantero se corta para que coincida con el ángulo de 60 grados el tornillo del receptor; previamente recortados con el contorno correcto y ángulos de ajuste contra la parte inferior de la zapata de retroceso y la escuadra con la bisagra de la base de apoyo. Se adapta a todos los rifles Ruger ® 77 y M77 Mark II ™ excepto modelos blanco VT.
Evaluaciones de clientes para BROWNELLS RUGER 77/M7 MARK II BEDDING PILLARS
Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 3
Front pillar needs some work(29/03/2012)
The rear pillar was just fine. The front pillar when placed properly on the recoil lug was too far forward casuing the action screw to touch the rear inide of the pillar, and would not align properly within the stock. Solution: Center the front pillar which also aligns it properly in the stock, then fill in the gap between the pillar and the rear of the recoil lug with bedding materail. Both pillars were intentionally long and required 30-40 thousands of shortening.
Incorrectly manufactured(03/04/2012)
The notch in the front pillar is too far back leaving a gap between the rear of the recoil lug and the pillar.
Very satisfied!(28/02/2013)
I have read the other reviews and haven't had those problems, I think these work exceptionally well.
Not close(09/06/2014)
Front pillar was way short, by at least 1/4" and narrow. I used them on the M77 in the past so I don't know why they changed. Ended up making my own.
Worked very well for me(18/04/2017)
These pillars fit perfectly in my early 70's vintage M77 and improved accuracy dramatically, as noted by the four mulies killed, one shot each, from 100 to 320 yards last fall. Check fit for length and recoil lug angle match prior to installing and you should be fine. I'm buying three more sets for my other 77's.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.