Su cesta está vacía.

Cesta

926-532900

Suscribirse al boletín

VLTOR WEAPON SYSTEMS
AR-15 GAS BLOCK LOW PROFILE

100003996

One-Piece Design Fits Under Free-Float Handguards

Slim replacement for cumbersome USGI front sight/gas block tower features a low profile for a more streamlined appearance and less chance of snagging on vegetation and other gear. Covers only 1" of barrel length and reduces weapon’s forward weight for improved handling and maneuverability. Clamp On models squeeze around the barrel with included socket head screws. Set Screw models use included set screws at the bottom of the unit to anchor the gas block to the barrel for the lowest-profile installation.

Más...

Diseño de una sola pieza que se ajusta debajo de las guardamanos flotantes

El reemplazo delgado para la torreta del bloque de gas/mira frontal USGI voluminosa presenta un perfil bajo para una apariencia más estilizada y menor probabilidad de enganche en vegetación y otros equipos. Cubre solo 1" de longitud del cañón y reduce el peso delantero del arma para mejorar el manejo y la maniobrabilidad. Los modelos Clamp On se ajustan alrededor del cañón con los tornillos de cabeza hueca incluidos. Los modelos Set Screw utilizan los tornillos de fijación incluidos en la parte inferior de la unidad para anclar el bloque de gas al cañón, logrando la instalación de más bajo perfil.

Más...

Evaluaciones de clientes para VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK

Número de evaluaciones: 12
De brownells.com: 12
Evaluación media: 4,1

Poor Quality Set Screws (12/02/2015)

I have a VLTOR one piece upper so I thought this would be a good match. The gas block itself looks good. Unfortunately, one of the set screws stripped when I applied minimal torque with an Allen (hex) key. The other set screw was fine. I'm not sure if this was an isolated defect, but I ended up having to drill one of the set screws out. This is very disappointing considering the slightly higher cost of the VLTOR block. To their credit Brownells' did accept this as a return.

Precision at it's Best (24/08/2015)

I compared this block first hand with seven other blocks before deciding to install the VLTOR block. The finish is superior to most; deep black phosphate and very uniform. The finish is equal to two other excellent choices, the Brownell's branded block and the Bravo Company block. The vertical grooves machined into the block add a pleasing and distinctive look and theoretically may offer some additional surface area for cooling. The machining appears very precise. Installation was straight forward and fit was tight and precise.

Nice gas block (12/07/2014)

This is a nicely done gas block but it touches my handguard (MI Gen 2 SS) very slightly at the screw heads. It is barely touching and I have checked that it is not canted, etc. Disappointing, but I will use it for another build I have planned. I usually prefer clamp on attachment, but the BCM barrel came with a dimple under the gas port so the set screw block I am replacing this with should work fine. A little filing would fix the issue, but I would rather not have to.

Less than useful (14/06/2010)

The fact the screws are on the side should have been screaming at me. It is not low profile at all, the screws protrude so far when mounted it was impossible to fit under the DD 10" Lite rail. The screws do not recess enough for proper clearance. The other version I have seen of this would fit fine as the screws are recessed and are on the bottom.

No problems (19/06/2010)

I have this installed on my SPR build which has a
White Oak Armament barrel with Midwest Industries free float handguards and everything works perfectly. My rifle cycles correctly and the bolts for the gas block has not come loose. I did however use vibra-lock on the threads.

Perfect! (07/07/2010)

After having a nasty experience with the "set screw style" gas block I decided to use a clamp on and went with the Vltor. This gas block is very well made. It was a bit tight for the gas tube to fit in which is normal and once the tube was in everything with very smoothly. Make sure to loctite the screws and this thing wil stay forever. I put this underneath my TRX Extreme which is extremely skinny. This will fit under most handguards. I don't believe this gas block is made to fit under the DD Lites and Omegas, and also the LaRues. For the handguards it is made to fit under, I'd prefer no other.

Great Low-Pro Steel Gas Block (16/01/2011)

I used this on a 16" Mid-Length Gas System AA 6.5 Grendel barrel. I have fired it in both extreme heat at 100 degrees F, down to 18 degrees F with never a malfunction using various loads. This is one of the best steel low-pro gas blocks on the market. The gas tube does fit tightly, which is a good thing for a reliable gas circuit. Loc-tite is your friend when tightening the screws after testing that you have a proper gas circuit. Read the limitations as to what handguards it will not fit under. The finish and logo are features that go above what other manufacturers offer on most of these types of products, which shows that VLTOR goes further in making a great part. Every VLTOR product I have used so far shows a higher attention to workmanship, finish, and functionality.

Super nice fit on Black Hole Weap bbl (10/08/2011)

I installed this VLTOR low profile, side clamping, gas block on a standard profile, stainless, 24 inch long, 6.8mm SPC, Black Hole Weaponry barrel. The fit was nice and snug even before I tightened the bolts. It stayed aligned while tightening. I then fit a rifle length gas tube and covered the whole set-up with a Midwest Ind. SS, 15 inch free floating hand-guard. This gas block fit underneath just fine. It fired and cycled from round one and I now have 300 rounds through the rifle without a single problem. No leaks of any gas. Alex Clark Homer, Alaska

Fits like a glove (12/08/2011)

I installed this gas block on a 0.75 inch diameter Black Hole weaponry barrel. It fit nice and snug.
The gas tube hole was nice and snug as well. After tightening I attempted to whack the gas block with a mallet to see if it would move. It did not. Now after 300 hot experimental hand-loads there is NO gas leakage. This gas block fit under a Midwest Industries SS type extended hand-guard without touching.

nice product (26/08/2011)

well made quality product. small, compact, fits right.

great piece (03/11/2013)

High value installs easy and worth every penny!

Solid but Flawed (24/08/2016)

Technically there's nothing wrong with this product. It's a solid, tightly-clamping, beautifully-fitting, streamlined gas block. The one enormous problem is that the standard hex screws it uses still have full-sized heads, heads which are (at least seemingly) in direct, if glancing, contact with the inside of my Midwest Industries MLOK guard. Now this pretty well eliminates any chance of the screws walking loose, but it also threatens the free-float nature of the guard. I so far haven't noticed an effect on accuracy, but I only run a red dot. And in addition to the 6 o'clock rail slot (or half of two of them on mine) being blocked by the bottom portion as is typical, the 4:30 and 3 o'clock slots are also unusable now on account of the screws. Lacking grip panels to guard against heat buildup, the middle 20 percent of my 15" rail is ungrip-able because of this gap. Still, if your technique allows for this or you just want a good, solid clamp design, you could definitely do worse.

Leer 12 mas calificaciones en brownells.com

119.9 119.9 1 EUR

N.º de producto: 100003996
VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK
Ref Fabricante: GB2C El reemplazo delgado para la torreta del bloque de gas/mira frontal USGI voluminosa presenta un perfil bajo para una apariencia más estilizada y menor probabilidad de enganche en vegetación y otros equipos. Cubre solo 1" de longitud del cañón y reduce el peso delantero del arma para mejorar el manejo y la maniobrabilidad. Los modelos Clamp On se ajustan alrededor del cañón con los tornillos de cabeza hueca incluidos. Los modelos Set Screw utilizan los tornillos de fijación incluidos en la parte inferior de la unidad para anclar el bloque de gas al cañón, logrando la instalación de más bajo perfil.

119.9 EUR 0 119,90 € *

Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.

Caracteristicas: Diametro interior: .750 Estilo: Low-Profile, Clamp Hacer: AR-15 Material: Steel

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Top takeaways

El AR-15 Gas Block Low Profile de VLTOR WEAPON SYSTEMS ofrece un diseño estilizado que reduce la probabilidad de enganche en vegetación y otros equipos.
Cubre solo 1" de longitud del cañón, lo que disminuye el peso delantero del arma y mejora su manejo y maniobrabilidad.
Disponible en dos modelos: Clamp On, que se ajusta con tornillos de cabeza hueca, y Set Screw, que utiliza tornillos de fijación para una instalación de perfil más bajo.

Atributos

Diametro interior: .750 Estilo: Clamp,Low-Profile Hacer: AR-15 Material: Steel Peso de entrega: 0,045kg Altura de envío: 20mm Ancho de envío: 84mm Longitud de envío: 183mm

Detalles del artículo

Hecho en USA
Clasificación de exportación de EE. UU.: 0A501.x

🔫 Mejora tu AR-15 con el AR-15 GAS BLOCK LOW PROFILE de VLTOR WEAPON SYSTEMS. Perfil bajo, acero, diámetro .750. ¡Mejor manejo y maniobrabilidad! 🚀 Aprende más.

One-Piece Design Fits Under Free-Float Handguards

Más...

Diseño de una sola pieza que se ajusta debajo de las guardamanos flotantes

Más...

Evaluaciones de clientes para VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK

Número de evaluaciones: 12
De brownells.com: 12
Evaluación media: 4,1

Poor Quality Set Screws (12/02/2015)

Precision at it's Best (24/08/2015)

Nice gas block (12/07/2014)

Less than useful (14/06/2010)

No problems (19/06/2010)

Perfect! (07/07/2010)

Great Low-Pro Steel Gas Block (16/01/2011)

Super nice fit on Black Hole Weap bbl (10/08/2011)

Fits like a glove (12/08/2011)

nice product (26/08/2011)

well made quality product. small, compact, fits right.

great piece (03/11/2013)

High value installs easy and worth every penny!

Solid but Flawed (24/08/2016)

Leer 12 mas calificaciones en brownells.com

Los clientes compraron
Alternativas

BROWNELLS AR-10 5/8"-24 BOTTOMING TAP
AR-15/M16 FLASH SUPPRESSOR TAP

BROWNELLS

En stock

38,90 € *

Taps

New

MAGPUL XTM ENHANCED RAIL PANEL PICATINNY POLYMER BLACK 1.5"
AR-15 PICATINNY XTM ENHANCED RAIL PANEL POLYMER

MAGPUL

En stock

19,90 € *

4,2

OTIS 308CAL/7.62MM RIPCORD 36"
RIPCORDS

OTIS

En stock

27,90 € * 26,90 € - 32,90 €*

Gratas para recamara

MIDWEST INDUSTRIES KEYMOD RAIL PICATINNY ALUMINUM BLACK 2.1"
AR-15 PICATINNY KEYMOD RAIL ALUMINUM

MIDWEST INDUSTRIES

En stock

39,90 € * 39,90 € - 45,90 €*

BRAVO COMPANY KEYMOD BCMGUNFIGHTER SHORT VERTICAL GRIP POLYMER BLACK
KEYMOD BCMGUNFIGHTER SHORT VERTICAL GRIP

BRAVO COMPANY

En stock

64,90 € * 64,90 € - 74,90 €*

Puños verticales

TROY INDUSTRIES AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK
AR-15 GAS BLOCK LOW PROFILE

TROY INDUSTRIES

Reordenado

64,90 € *

Gas Blocks

3,9

BADGER ORDNANCE AR-15 GAS BLOCK MK12 .750 STEEL BLACK
AR-15 GAS BLOCK MK12

BADGER ORDNANCE

En stock

109,90 € * 99,90 € - 109,90 €*

Gas Blocks

Identificarse

¿Ha olvidado su contraseña?
Registrarse

Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.

Redes Sociales

Navegacion

Categorias

Ordering

Servicio al cliente

¡Bienvenido!

Bienvenido a Brownells, la principal Armeria de accesorios de armas de fuego, piezas de armas y herramientas para armeros en España. En nuestra web podrá encontrar todo tipo de accesorios y repuestos para sus rifles, carabinas, escopetas o armas cortas. Si le gusta la caza o el tiro de precisión esta es su web.

La promesa de Brownells España

La promesa Brownells para nuestros clientes: TU SATISFACIÓN ESTÁ GARANTIZADA. Si por cualquier motivo no estás 100% satisfecho con cualquiera de los productos comprados a nosotros, se lo devolvemos o cambiamos.

Nuestra oferta

Si te gusta disparar, trabajar con armas como negocio o hobby, o simplemente poseer un arma, este es tu lugar. Durante más de 75 años, tiradores, armeros profesionales, aficionados, cuerpos de defensa y especialistas en armas han venido a Brownells.es por la alta calidad en sus piezas de armas y en los repuestos que ellos necesitan.

Encontrarás más de 90,000 incluyendo exclusivas piezas de armas, accesorios, herramientas para armeros, munición y otros productos para el manteniminto, reparación y mejora de tus pistolas.

Su equipo Brownells España

Armeria A. Izquierdo (B-13309356)

Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.

Vista clásica

Vista móvil