Non-marring, Delrin sleeves surround scopes to adapt them to fit bigger-diameter rings. Black, matte finish won t clash with your scope or gun. Reducers are sliced in half for easy, drop-on installation onto virtually any brand of rings in the sizes listed below. Sold as front-and-rear-ring kits.
SPECS: Kit includes front and rear reducer sets. Delrin, matte, black finish.
Más...
Adapta Anillos Mayores Para Tubos de Visor Menores
Mangas de Delrin que no marcan, rodean los visores para adaptarlos a anillos de mayor diámetro. Acabado negro mate que no desentona con tu visor o arma. Los reductores están cortados por la mitad para una instalación fácil y rápida en prácticamente cualquier marca de anillos de los tamaños listados a continuación. Se venden en kits para anillos delanteros y traseros.
ESPECIFICACIONES: El kit incluye conjuntos reductores delanteros y traseros. Delrin, acabado mate, color negro.
Más...
Evaluaciones de clientes para BROWNELLS DELRIN RING REDUCER 1" TO 7/8"
Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 4,4
good idea but!(02/12/2017)
Idea is good how ever on my 30-06 cooper I was unable to screw it tight enough for the scope not to move forward during recoil.
Not sure how they can improve that.
Works on my setup(26/09/2018)
These are installed in a 30mm Bobro quick detach ring mount holding my Kahles 26mm ZF69 scope. It does take a little more time and attention to detail to "perfectly" align the split ring inserts and scope and keep them aligned while carefully torquing the ring screws. My scope has not shifted in the rings in over four years of use. I cleaned the rings and reducer inserts with denatured alcohol before mounting the scope.
I would buy this product again(22/07/2010)
Used on my Savage 3C and Stevens 56 with the Weaver no 2 side mount base and 1" short ring set. Allows bolt handle clearance when used with a 3/4" scope and holds perfect zero.
Nice product(22/11/2011)
Perfect for installing a 3/4" vintage scope on 1" rings.
OUTSTANDING PRODUCT(30/01/2012)
I used these on a 7/8 inch rifle scope....couldn't find 7/8 inch rings so I just installed these and used one inch rings....outstanding results. I can strongly recommend the product. I installed them on a .30-06 and the rings and mount on the rifle is solid as a rock. You will need to cut off the overlapping excess of the delrin sleeve so make sure you have a sharp knife...you will like the result. Buy it.
Delrin Ring Reducer 1(25/03/2012)
I have a light weight 1970-80? Tasco widefield 2 to 7 power scope which has outstanding clarity mounted to my Winchester 9422M. I broke the original one piece mount off the scope because the screws had become worn and I wanted a better mount. I didnot realize that nobody makes 7/8" scope tube rings that fit a 3/8" dovetail base. The Delrin Ring Reducer will allow me to use a wide range of 1" mounts.
Get Some and Keep Them On Hand(31/10/2009)
These things work perfectly well, and they hold zero. Personally, I just buy all my scopes in 30mm, and then if I want to switch to a 1" scope, I use these with no issues.
worked great(02/01/2014)
I guess in my mind had them as being made of metal. when I opened them i thought dang plastic. BUT. I put them on and they worked great. The material they are made of holds the scope in my mind better than a metal one would anyway. Easy to put in and use and they look good no one even realizes they are there if the check out the scope I have on my AR. I would recommend them to any one who has a scope that wont fit the rings they want to use. They are better than I hoped for.
N.º de producto: 084000092 BROWNELLS DELRIN RING REDUCER 1" TO 7/8" Mangas de Delrin que no marcan, rodean los visores para adaptarlos a anillos de mayor diámetro. Acabado negro mate que no desentona con tu visor o arma. Los reductores están cortados por la mitad para una instalación fácil y rápida en prácticamente cualquier marca de anillos de los tamaños listados a continuación. Se venden en kits para anillos delanteros y traseros.
23.9EUR1223,90 €
*
Plazo de entrega de aproximadamente 14-21 días. Más de 10 pcs. en almacén de EE.UU.
Caracteristicas:Acabado: Matte BlackEstilo: DelrinTalla: 1'' to 7/8''
Acabado:
Matte Black
Estilo:
Delrin
Talla:
1'' to 7/8''
Peso de entrega: 0,005kgAltura de envío: 28mmAncho de envío: 76mmLongitud de envío: 142mm
Detalles del artículo
Hecho en USA
N.º de producto: 084000091 BROWNELLS DELRIN RING REDUCER 30MM TO 1" Mangas de Delrin que no marcan, rodean los visores para adaptarlos a anillos de mayor diámetro. Acabado negro mate que no desentona con tu visor o arma. Los reductores están cortados por la mitad para una instalación fácil y rápida en prácticamente cualquier marca de anillos de los tamaños listados a continuación. Se venden en kits para anillos delanteros y traseros.
27.9EUR527,90 €
*
Plazo de entrega de aproximadamente 14-21 días. 5 pcs. en el almacén de EE.UU.
Caracteristicas:Acabado: Matte BlackEstilo: DelrinTalla: 30mm to 1''
N.º de producto: 084000093 BROWNELLS DELRIN RING REDUCER 1" TO 3/4" Mangas de Delrin que no marcan, rodean los visores para adaptarlos a anillos de mayor diámetro. Acabado negro mate que no desentona con tu visor o arma. Los reductores están cortados por la mitad para una instalación fácil y rápida en prácticamente cualquier marca de anillos de los tamaños listados a continuación. Se venden en kits para anillos delanteros y traseros.
25.9EUR425,90 €
*
Plazo de entrega de aproximadamente 14-21 días. 4 pcs. en el almacén de EE.UU.
Caracteristicas:Acabado: Matte BlackEstilo: DelrinTalla: 1'' to 3/4''
N.º de producto: 084000094 BROWNELLS DELRIN RING REDUCER 30MM TO 26MM Mangas de Delrin que no marcan, rodean los visores para adaptarlos a anillos de mayor diámetro. Acabado negro mate que no desentona con tu visor o arma. Los reductores están cortados por la mitad para una instalación fácil y rápida en prácticamente cualquier marca de anillos de los tamaños listados a continuación. Se venden en kits para anillos delanteros y traseros.
22.9EUR122,90 €
*
Plazo de entrega de aproximadamente 14-21 días. 1 pcs. en el almacén de EE.UU.
Caracteristicas:Acabado: Matte BlackEstilo: DelrinTalla: 30mm to 26mm
Non-marring, Delrin sleeves surround scopes to adapt them to fit bigger-diameter rings. Black, matte finish won t clash with your scope or gun. Reducers are sliced in half for easy, drop-on installation onto virtually any brand of rings in the sizes listed below. Sold as front-and-rear-ring kits.
SPECS: Kit includes front and rear reducer sets. Delrin, matte, black finish.
Más...
Adapta Anillos Mayores Para Tubos de Visor Menores
Mangas de Delrin que no marcan, rodean los visores para adaptarlos a anillos de mayor diámetro. Acabado negro mate que no desentona con tu visor o arma. Los reductores están cortados por la mitad para una instalación fácil y rápida en prácticamente cualquier marca de anillos de los tamaños listados a continuación. Se venden en kits para anillos delanteros y traseros.
ESPECIFICACIONES: El kit incluye conjuntos reductores delanteros y traseros. Delrin, acabado mate, color negro.
Más...
Evaluaciones de clientes para BROWNELLS DELRIN RING REDUCER 1" TO 7/8"
Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 4,4
good idea but!(02/12/2017)
Idea is good how ever on my 30-06 cooper I was unable to screw it tight enough for the scope not to move forward during recoil.
Not sure how they can improve that.
Works on my setup(26/09/2018)
These are installed in a 30mm Bobro quick detach ring mount holding my Kahles 26mm ZF69 scope. It does take a little more time and attention to detail to "perfectly" align the split ring inserts and scope and keep them aligned while carefully torquing the ring screws. My scope has not shifted in the rings in over four years of use. I cleaned the rings and reducer inserts with denatured alcohol before mounting the scope.
I would buy this product again(22/07/2010)
Used on my Savage 3C and Stevens 56 with the Weaver no 2 side mount base and 1" short ring set. Allows bolt handle clearance when used with a 3/4" scope and holds perfect zero.
Nice product(22/11/2011)
Perfect for installing a 3/4" vintage scope on 1" rings.
OUTSTANDING PRODUCT(30/01/2012)
I used these on a 7/8 inch rifle scope....couldn't find 7/8 inch rings so I just installed these and used one inch rings....outstanding results. I can strongly recommend the product. I installed them on a .30-06 and the rings and mount on the rifle is solid as a rock. You will need to cut off the overlapping excess of the delrin sleeve so make sure you have a sharp knife...you will like the result. Buy it.
Delrin Ring Reducer 1(25/03/2012)
I have a light weight 1970-80? Tasco widefield 2 to 7 power scope which has outstanding clarity mounted to my Winchester 9422M. I broke the original one piece mount off the scope because the screws had become worn and I wanted a better mount. I didnot realize that nobody makes 7/8" scope tube rings that fit a 3/8" dovetail base. The Delrin Ring Reducer will allow me to use a wide range of 1" mounts.
Get Some and Keep Them On Hand(31/10/2009)
These things work perfectly well, and they hold zero. Personally, I just buy all my scopes in 30mm, and then if I want to switch to a 1" scope, I use these with no issues.
worked great(02/01/2014)
I guess in my mind had them as being made of metal. when I opened them i thought dang plastic. BUT. I put them on and they worked great. The material they are made of holds the scope in my mind better than a metal one would anyway. Easy to put in and use and they look good no one even realizes they are there if the check out the scope I have on my AR. I would recommend them to any one who has a scope that wont fit the rings they want to use. They are better than I hoped for.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.