Extrae las costillas de ventilación abolladas de las escopetas en solo minutos. Fácil de colocar y rápido de usar. El puente de latón no marca la parte superior de la costilla; las mordazas de acero se ajustan automáticamente.
ESPECIFICACIONES: Puente; Latón mecanizado de 3" (7.6cm) de largo y ¼" (6.3mm) de grosor. Mordazas; Acero mecanizado y endurecido de 1½" (3.8cm) de largo y ½" (12.7mm) de ancho en el punto más ancho.
Más...
Evaluaciones de clientes para MURRAYS VENT RIB TOOL
Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 5
Cheaper than a new rib!(09/03/2010)
I used this tool to remove two severe dents in the rib of my Ruger O/U. I was very tentative at first, but once I got used to the pressure it worked like a charm. You do have to slightly over tighten to ensure the dent is removed. A heavy hand could convert a dent to a hump. Patience and checking with a steel rule will keep you in a great place.
Handy little tool(10/07/2012)
Neatest thing since a pocket on a shirt. Pulls dinged ribs right up. Like the other reviewer noted, you do need to pull it up a little higher than flat and check it with a flat edge, but works like it's supposed to.
works graet, easy to use (01/12/2014)
I have used this tool about 10 times and it has worked great, easy and fast, One great tool.
Better than a gunsmith (13/06/2015)
Simple to use tool that works! I used this on my baby a Perazzi, did not want to ship the gun off. Prior dent is not noticeable after a bit of cold blue touch up. Use with caution, adjust, measure and repeat.
Christmas surprise (26/12/2016)
Unsightly crimp in my over under vent rib near the mid sight. Took it to three gunsmiths. Two refused to fix it and one wanted $150 and to remove my mid sight mark. I said no and lived with the crimp for a year. Then this Christmas my wife ordered the Murray vent rib tool from Brownells.. Was just going to test the fit of the tool and realized I could fix it. Took me seconds and my barrell was good as new. Every shotgunner with vent ribs needs this tool.
N.º de producto: 563100000 MURRAYS VENT RIB TOOL Ref Fabricante: NONE Extrae las costillas de ventilación abolladas de las escopetas en solo minutos. Fácil de colocar y rápido de usar. El puente de latón no marca la parte superior de la costilla; las mordazas de acero se ajustan automáticamente.
99.9EUR3499,90 €
*
Plazo de entrega de aproximadamente 14-21 días. Más de 10 pcs. en almacén de EE.UU.
Extrae las costillas de ventilación abolladas de las escopetas en solo minutos. Fácil de colocar y rápido de usar. El puente de latón no marca la parte superior de la costilla; las mordazas de acero se ajustan automáticamente.
ESPECIFICACIONES: Puente; Latón mecanizado de 3" (7.6cm) de largo y ¼" (6.3mm) de grosor. Mordazas; Acero mecanizado y endurecido de 1½" (3.8cm) de largo y ½" (12.7mm) de ancho en el punto más ancho.
Más...
Evaluaciones de clientes para MURRAYS VENT RIB TOOL
Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 5
Cheaper than a new rib!(09/03/2010)
I used this tool to remove two severe dents in the rib of my Ruger O/U. I was very tentative at first, but once I got used to the pressure it worked like a charm. You do have to slightly over tighten to ensure the dent is removed. A heavy hand could convert a dent to a hump. Patience and checking with a steel rule will keep you in a great place.
Handy little tool(10/07/2012)
Neatest thing since a pocket on a shirt. Pulls dinged ribs right up. Like the other reviewer noted, you do need to pull it up a little higher than flat and check it with a flat edge, but works like it's supposed to.
works graet, easy to use (01/12/2014)
I have used this tool about 10 times and it has worked great, easy and fast, One great tool.
Better than a gunsmith (13/06/2015)
Simple to use tool that works! I used this on my baby a Perazzi, did not want to ship the gun off. Prior dent is not noticeable after a bit of cold blue touch up. Use with caution, adjust, measure and repeat.
Christmas surprise (26/12/2016)
Unsightly crimp in my over under vent rib near the mid sight. Took it to three gunsmiths. Two refused to fix it and one wanted $150 and to remove my mid sight mark. I said no and lived with the crimp for a year. Then this Christmas my wife ordered the Murray vent rib tool from Brownells.. Was just going to test the fit of the tool and realized I could fix it. Took me seconds and my barrell was good as new. Every shotgunner with vent ribs needs this tool.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.