Recuts Lug For A Tight Fitting Barrel That Improves Accuracy
Hand operated, carbide cutter easily trims excess material from the bottom barrel lug when fitting custom or factory barrels to 1911 Autos. Cuts barrel lugs parallel, and with the correct height and radius, to help produce the best possible lockup. Use .186" cutter first, then progress to the .195" cutter if more material needs to be removed. Follow with careful hand fitting to achieve a firm, non-binding barrel-to-slide fit. Start small and check your work often. It is possible, with some slide/barrel combinations, that the .195" cutter could remove more material than necessary. Fits all 1911 Auto, Commander and Officers ACP, single- and double-stack frames.
SPECS: 1" (2.5cm) diameter knob; 2.07" (5.25cm) long shank. .186" (4.72mm) or .195" (4.95mm) diameter cutters. Complete instructions included.
Más...
Rehace el Resalte para un Cañón Ajustado con Precisión que Mejora la Precisión
Operado a mano, el cortador de carburo elimina fácilmente el material excesivo del resalte inferior del cañón al ajustar cañones personalizados o de fábrica a las pistolas 1911. Corta los resaltes del cañón de manera paralela, y con la altura y radio correctos, para ayudar a producir el mejor acoplamiento posible. Usa primero el cortador de .186", luego avanza al cortador de .195" si es necesario eliminar más material. Continúa con un ajuste manual cuidadoso para lograr un ajuste firme y sin atascos entre el cañón y la corredera. Empieza con poco y revisa tu trabajo con frecuencia. Es posible, con algunas combinaciones de corredera/cañón, que el cortador de .195" pueda eliminar más material del necesario. Compatible con todas las pistolas 1911 Auto, Commander y Officers ACP, armazones de simple y doble columna.
ESPECIFICACIONES: Perilla de 1" (2.5cm) de diámetro; vástago de 2.07" (5.25cm) de largo. Cortadores de .186" (4.72mm) o .195" (4.95mm) de diámetro. Instrucciones completas incluidas.
Más...
Evaluaciones de clientes para BROWNELLS 1911 LUG CUTTER HANDLE W/0.195" CUTTER
Número de evaluaciones: 4
De brownells.com: 4
Evaluación media: 2,8
Do not buy!!(14/11/2013)
The new cutters are brittle and will break one first time use.
A must tool for gunsmiths(20/12/2011)
This lug cutter is easy to use and does a professional job.
Change In Design (09/10/2014)
The design of the .186 cutter was changed to a helix design. I cut 3 lower lugs on barrels and the teeth sheared off in one area on the third barrel. The old "burr" style cutter must have fit 30-40 barrels before it broke. Please bring back the old style. Helix is fine for the .195 cutter as it delivers a smoother cut.
Works well(25/01/2015)
I've had this lug cutter for a few years and it has worked well for me. It should be used with the handle on the left side of the frame as viewed from the rear other wise the cutter will grab the barrel lug pulling it forward and braking the cutter. Clean and oil it often and it will cut cleanly. It would be nice if the support bushing was attached to the cutter, I also had to turn a shoulder on the bushing in order for it to clear the slide and have full engagement in the frame, although it did work the way it was.
N.º de producto: 080000068 BROWNELLS 1911 LUG CUTTER HANDLE W/0.195" CUTTER Operado a mano, el cortador de carburo elimina fácilmente el material excesivo del resalte inferior del cañón al ajustar cañones personalizados o de fábrica a las pistolas 1911. Corta los resaltes del cañón de manera paralela, y con la altura y radio correctos, para ayudar a producir el mejor acoplamiento posible. Usa primero el cortador de .186", luego avanza al cortador de .195" si es necesario eliminar más material. Continúa con un ajuste manual cuidadoso para lograr un ajuste firme y sin atascos entre el cañón y la corredera. Empieza con poco y revisa tu trabajo con frecuencia. Es posible, con algunas combinaciones de corredera/cañón, que el cortador de .195" pueda eliminar más material del necesario. Compatible con todas las pistolas 1911 Auto, Commander y Officers ACP, armazones de simple y doble columna.
114.9EUR16114,90 €
*
Plazo de entrega de aproximadamente 14-21 días. Más de 10 pcs. en almacén de EE.UU.
N.º de producto: 080000067 BROWNELLS 1911 LUG CUTTER HANDLE W/0.186" CUTTER Operado a mano, el cortador de carburo elimina fácilmente el material excesivo del resalte inferior del cañón al ajustar cañones personalizados o de fábrica a las pistolas 1911. Corta los resaltes del cañón de manera paralela, y con la altura y radio correctos, para ayudar a producir el mejor acoplamiento posible. Usa primero el cortador de .186", luego avanza al cortador de .195" si es necesario eliminar más material. Continúa con un ajuste manual cuidadoso para lograr un ajuste firme y sin atascos entre el cañón y la corredera. Empieza con poco y revisa tu trabajo con frecuencia. Es posible, con algunas combinaciones de corredera/cañón, que el cortador de .195" pueda eliminar más material del necesario. Compatible con todas las pistolas 1911 Auto, Commander y Officers ACP, armazones de simple y doble columna.
114.9EUR49114,90 €
*
Plazo de entrega de aproximadamente 14-21 días. Más de 10 pcs. en almacén de EE.UU.
Recuts Lug For A Tight Fitting Barrel That Improves Accuracy
Hand operated, carbide cutter easily trims excess material from the bottom barrel lug when fitting custom or factory barrels to 1911 Autos. Cuts barrel lugs parallel, and with the correct height and radius, to help produce the best possible lockup. Use .186" cutter first, then progress to the .195" cutter if more material needs to be removed. Follow with careful hand fitting to achieve a firm, non-binding barrel-to-slide fit. Start small and check your work often. It is possible, with some slide/barrel combinations, that the .195" cutter could remove more material than necessary. Fits all 1911 Auto, Commander and Officers ACP, single- and double-stack frames.
SPECS: 1" (2.5cm) diameter knob; 2.07" (5.25cm) long shank. .186" (4.72mm) or .195" (4.95mm) diameter cutters. Complete instructions included.
Más...
Rehace el Resalte para un Cañón Ajustado con Precisión que Mejora la Precisión
Operado a mano, el cortador de carburo elimina fácilmente el material excesivo del resalte inferior del cañón al ajustar cañones personalizados o de fábrica a las pistolas 1911. Corta los resaltes del cañón de manera paralela, y con la altura y radio correctos, para ayudar a producir el mejor acoplamiento posible. Usa primero el cortador de .186", luego avanza al cortador de .195" si es necesario eliminar más material. Continúa con un ajuste manual cuidadoso para lograr un ajuste firme y sin atascos entre el cañón y la corredera. Empieza con poco y revisa tu trabajo con frecuencia. Es posible, con algunas combinaciones de corredera/cañón, que el cortador de .195" pueda eliminar más material del necesario. Compatible con todas las pistolas 1911 Auto, Commander y Officers ACP, armazones de simple y doble columna.
ESPECIFICACIONES: Perilla de 1" (2.5cm) de diámetro; vástago de 2.07" (5.25cm) de largo. Cortadores de .186" (4.72mm) o .195" (4.95mm) de diámetro. Instrucciones completas incluidas.
Más...
Evaluaciones de clientes para BROWNELLS 1911 LUG CUTTER HANDLE W/0.195" CUTTER
Número de evaluaciones: 4
De brownells.com: 4
Evaluación media: 2,8
Do not buy!!(14/11/2013)
The new cutters are brittle and will break one first time use.
A must tool for gunsmiths(20/12/2011)
This lug cutter is easy to use and does a professional job.
Change In Design (09/10/2014)
The design of the .186 cutter was changed to a helix design. I cut 3 lower lugs on barrels and the teeth sheared off in one area on the third barrel. The old "burr" style cutter must have fit 30-40 barrels before it broke. Please bring back the old style. Helix is fine for the .195 cutter as it delivers a smoother cut.
Works well(25/01/2015)
I've had this lug cutter for a few years and it has worked well for me. It should be used with the handle on the left side of the frame as viewed from the rear other wise the cutter will grab the barrel lug pulling it forward and braking the cutter. Clean and oil it often and it will cut cleanly. It would be nice if the support bushing was attached to the cutter, I also had to turn a shoulder on the bushing in order for it to clear the slide and have full engagement in the frame, although it did work the way it was.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.