Brownells Iberica - El mayor proveedor de accesorios para el Tiro, Piezas y herramientas del armero. España

BROWNELLS
CERROSAFE® CHAMBER CASTING ALLOY

080027050
Never Wears Out- Use Over And Over
There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
25.51 46.9 2 EUR
Sale
N.º de producto: 080027050
BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1/2LB Existen diversos productos en el mercado que se pueden utilizar para hacer un molde de la cámara de un arma de fuego. Para asegurarnos de que el producto que te ofrecemos es el mejor y más práctico, contactamos al fabricante básico. Nos recomendaron Cerrosafe debido a sus características únicas. A diferencia de Woodsmetal, que se expande al enfriarse y no puede ser retirado de la cámara del arma, Cerrosafe se contrae durante los primeros 30 minutos de enfriamiento y luego, al final de una hora, tiene EXACTAMENTE el tamaño de la cámara. Al cabo de 200 horas, habrá expandido aproximadamente 0.0025". Este factor es bien conocido por todos los fabricantes de herramientas y lo tendrán en cuenta al hacer matrices, escariadores o calibres a partir de tu molde, si les dices que el molde es de Cerrosafe. Cerrosafe se funde entre 158° - 190° F. Debe fundirse en un cucharón de hierro limpio. La fuente de calor debe ser retirada tan pronto como la aleación esté completamente fundida, momento en el cual está lista para verter. La fundición solidificada debe ser retirada de la cámara antes de, o cuando, se enfríe a temperatura ambiente. Si se permite que permanezca en el molde durante más de una hora, se adherirá a las paredes de la cámara y será difícil de retirar. Limpia la cámara del rifle a fondo, luego tapona el cañón inmediatamente delante de la garganta con un pequeño trapo, pero no tan apretado que no pueda ser expulsado. Si es posible, vierte el Cerrosafe fundido a través de un pequeño tubo en el fondo del molde, retirando gradualmente el tubo a medida que la cámara se llena. Si el cañón está frío, caliéntalo a temperatura ambiente o superior antes de hacer el molde. Cuando se enfríe, retira de la cámara, utilizando una varilla o palo desde el extremo del cañón.
25.51 EUR 77 25,51 € * 27,90 €
Solo 10 unidades disponibles a este precio
Plazo de entrega de aproximadamente 2-4 días.
Más de 10 piezas en almacén local

Atributos

Peso de entrega: 0,181kg Altura de envío: 13mm Ancho de envío: 38mm Longitud de envío: 137mm

Detalles del artículo

Hecho en USA




N.º de producto: 080027100
BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1LB Existen diversos productos en el mercado que se pueden utilizar para hacer un molde de la cámara de un arma de fuego. Para asegurarnos de que el producto que te ofrecemos es el mejor y más práctico, contactamos al fabricante básico. Nos recomendaron Cerrosafe debido a sus características únicas. A diferencia de Woodsmetal, que se expande al enfriarse y no puede ser retirado de la cámara del arma, Cerrosafe se contrae durante los primeros 30 minutos de enfriamiento y luego, al final de una hora, tiene EXACTAMENTE el tamaño de la cámara. Al cabo de 200 horas, habrá expandido aproximadamente 0.0025". Este factor es bien conocido por todos los fabricantes de herramientas y lo tendrán en cuenta al hacer matrices, escariadores o calibres a partir de tu molde, si les dices que el molde es de Cerrosafe. Cerrosafe se funde entre 158° - 190° F. Debe fundirse en un cucharón de hierro limpio. La fuente de calor debe ser retirada tan pronto como la aleación esté completamente fundida, momento en el cual está lista para verter. La fundición solidificada debe ser retirada de la cámara antes de, o cuando, se enfríe a temperatura ambiente. Si se permite que permanezca en el molde durante más de una hora, se adherirá a las paredes de la cámara y será difícil de retirar. Limpia la cámara del rifle a fondo, luego tapona el cañón inmediatamente delante de la garganta con un pequeño trapo, pero no tan apretado que no pueda ser expulsado. Si es posible, vierte el Cerrosafe fundido a través de un pequeño tubo en el fondo del molde, retirando gradualmente el tubo a medida que la cámara se llena. Si el cañón está frío, caliéntalo a temperatura ambiente o superior antes de hacer el molde. Cuando se enfríe, retira de la cámara, utilizando una varilla o palo desde el extremo del cañón.
46.9 EUR 126 46,90 € *
Plazo de entrega de aproximadamente 14-21 días.
Más de 10 pcs. en almacén de EE.UU.

Atributos

Peso de entrega: 0,454kg Altura de envío: 8mm Ancho de envío: 76mm Longitud de envío: 226mm

Detalles del artículo

Hecho en USA

Never Wears Out- Use Over And Over
There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
Newsletters