Su cesta está vacía.

Cesta

926-532900

Suscribirse al boletín

VOLQUARTSEN
EXACT EDGE EXTRACTOR MKII, MKIII, MKIV, 10/22®

810162010546 930000010

Tuned & Hardened For Lasting Performance

Machined with exacting tolerances; hook is .005" closer to rim to give a positive, non-slip grip on the case head. The very precise hook point is hardened to Rc 58-60, will not lose its edge, even after years of use.

SPECS: A-2 tool steel, in-the-white. Fits Ruger MKII, MKIII, MKIV and 22/45 pistols; 10/22 and 10/22 magnum.

Más...

Atentos & endurecido para un rendimiento duradero

Mecanizado con exigentes tolerancias; el gancho es. 005" más cercano al borde para dar un agarre antideslizante y positivo sobre la cabeza de la caja. El punto preciso gancho es endurecida a 58-60 Rc, no perderá su filo, incluso después de años de uso.

Especificaciones: A-2 herramienta de acero, en el blanco. Incluye resorte de repuesto. Se adapta a las pistolas Ruger MKII, MKIII, MKIV y 22/45; 10/22® y 10/22® Magnum.

Más...

Evaluaciones de clientes para VOLQUARTSEN EXACT EDGE EXTRACTOR

Número de evaluaciones: 12
De brownells.com: 12
Evaluación media: 5

Works GREAT in Ruger auto pistols too ! (25/10/2009)

These extractors work GERAT in my Ruger Mk II and Mk III 22 autos. Use the extractor only - must use the original factory extractor spring. Work so well that I have replaced the extractors in all six of my pistols. Any extraction problem will just disappear.

Volquartsen Is Good Medicine! (24/08/2010)

It seems like the newer Ruger 10/22 extractors are made from soft metal and the edges dull quickly. After 2000 rounds or so, jams can become problematic--even with ammo that was jam-free when the rifle was new. The Exact Edge Extractor is the fix!

No more stuck shells. (22/01/2012)

This was easy to install and after testing it I have yet to have another failure to extract.

Extractor (10/02/2013)

A lot sharper and more surface area over the Factory Ruger extractor. More consistent ejection and jams are now non existent.

Broken to improved with one little part (15/03/2013)

I didn't get this to improve my 10/22, i bought it because my old extractor flew out of my rifle during a plinking spree. I just assumed that Ruger 1022's just failed to eject periodically due to ammo or low grade systems or that I ran about 5,000 rounds through it over 20 some years with only barrel cleaning and wiping lubrication only of the visible assembled carriage system. What a difference. This thing grabs the rim firmly and squarely and under close examination, the precise and sharp, greater than 90 degree tooth plants it's pointed tooth perfectly and aggressively into the base of the chambered round's rim and pulls it cleanly out like a wolf ripping flesh. The Volquartsen spring, although shorter has far more force than the original spring creating a more sure and precise "bite". Closing the bolt slowly, you can hear the extractor snapping in place. Such a small part but what a major improvement. Not a single failure yet. I'm glad my original piece broke so, with the help of YouTube, I could fully disassemble the rifle and do a full de-grease and re-lube with Slip2000 and some TW25b weapon grease then upgrade a small but very important and quality part to revive my enjoyment of this classic piece that will soon belong to my son. Now I brought new life into a favorite toy!

THIS IS THE FIX (18/02/2014)

This extractor is very quality made. It is easy to see if you lay it next to the stock unit there is no comparison. They are similar but there is a big difference, anyway it fixed my 10/22 made it better than new went from 3 or more jams/stovepipes per 10 clip to zero jams due to faulty extractor hold. Also a big thank you to Brownell's for quick proccess and shipping, I got it in four days from time ordered. Thanks to Volquartsen for a quality made product.

Easy Install & Works Great (12/04/2014)

I installed the extractor in a Mk2. It took about 20 minutes from start to finish. Then I took the gun to the range and had ZERO FTE's. Before I was having 3 or more FTE per magazine. Extremely satisfied with the VQ Extractor.

Perfect (13/07/2015)

Seriously perfect. I would have anywhere from 1-4 FTE's per 10 clip before. I went shooting, and put 300 rounds of varying brands through it, and had 0 FTE's. If there was only one mod I could do to a 10/22, it would be this.

The spring that came with the extractor was too short though, so I just used the stock one.

Could be A MIRACLE! (25/10/2015)

I had my doubts about this VQ Extractor putting an end to the FTE's all too frequently in our 10/22 Takedown. We purchased the rifle in early March and we've encountered this problem at least once at almost every single session at the range since then. (Other than this frustrating characteristic, the rifle has become an inanimate member of the family; we do like it.)

Cleaning helped at times, but was apparently not THE solution. So, we got pretty good at clearing jams.

However, as the factory extractor showed more and more wear-and-tear, including the claw rounding off. (Image attached, in case it is happening to you.) I knew I'd have to do something. Then, during a session in early October, I not only had a spike in FTE's, I twice had chambered rounds that would not extract when I manually racked the bolt; it was time to do something.

I initially planned to just buy a couple factory extractors but, having read so much good about the VQ extractor, I bought one of each. Last weekend, I replaced the original "rounder" with the VQ. Yesterday, I was able to test it. IT'S A MIRACLE! Okay, it was one session, but I sent 210rds of mixed makes & types of ammo, including some that were physically/mechanically "questionable", and I had 0, zero, nil, nada, FTE's.

Very, very cool.

<img width="500" src='/userdocs/reviewimages/04fbcc6b-2169-43bd-a99f-f5161dde82cf.jpg' alt=''>

PERFECT (25/06/2016)

My 10/22 would FTE at least once per mag. Read all the good previous reviews. Ordered additional for my MKIII. Compared the extractor lip of the VQ to the factory extractor on both guns. Increase in quality, purchase on rim and strength of spring was more than quite obvious. Note: The provided spring is shorter than factory but STRONGER. "NO MORE FTE's !"

Flawless (21/04/2017)

This simple upgrade made all of the difference. I recently upgraded the stock barrel and after making the switch I experienced numerous FTEs. Before trying more extreme options I tried this simple upgrade. Turns out this $12 part was all I neede. Just put a few hundred rounds through it without a single issue. Nothing gets past this claw!

No Malfunctions During Last Outing! (17/07/2018)

After receiving a Ruger Mark III Target for a gift in 2009 I left it stock for nearly a decade. It has accounted for a few different species of animals as well as paper and steel targets. During the past few years there seemed to be an increase in the number of malfunctions - failures to extract or eject the brass. After ordering and receiving the Volquartsen Exact Edge Extractor I installed it myself with a referral to some of the online videos detailing the steps. It is a little more time consuming getting the old extractor out than getting the Volquartsen extractor in but not too bad. I followed the instructions on the box which suggested using the Ruger extractor spring when installing the Volquartsen extractor on the Mark series pistols. My first outing to fire the Mark III after the Volquartsen extractor install was a brief 100 rounds in fairly rapid succession. I fired 50 rounds of CCI MiniMags and 50 rounds of low cost Federal ammunition (the modern equivalent of the old Federal Lightning). The pistol had no malfunctions of any kind! It has been a long time since that happened. I firmly believe this Volquartsen Exact Edge Extractor has vastly improved the reliability of this pistol.

Leer 12 mas calificaciones en brownells.com

24.9 24.9 1 EUR

N.º de producto: 930000010
VOLQUARTSEN EXACT EDGE EXTRACTOR
Ref Fabricante: VC10EE 810162010546 Mecanizado con exigentes tolerancias; el gancho es. 005" más cercano al borde para dar un agarre antideslizante y positivo sobre la cabeza de la caja. El punto preciso gancho es endurecida a 58-60 Rc, no perderá su filo, incluso después de años de uso.

24.9 EUR 56 24,90 € *

Plazo de entrega de aproximadamente 14-21 días.
Más de 10 pcs. en almacén de EE.UU.

Caracteristicas: Hacer: Ruger Modelo: Mark III, Mark II, 10/22, 10/22 Magnum, Mark IV

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Atributos

Hacer: Ruger Modelo: 10/22,Mark II,Mark III,Mark IV,10/22 Magnum Peso de entrega: 0,005kg Altura: 10mm Anchura: 71mm Longitud: 89mm

Detalles del artículo

Hecho en USA
Clasificación de exportación de EE. UU.: 0A501.x

Tuned & Hardened For Lasting Performance

SPECS: A-2 tool steel, in-the-white. Fits Ruger MKII, MKIII, MKIV and 22/45 pistols; 10/22 and 10/22 magnum.

Más...

Atentos & endurecido para un rendimiento duradero

Especificaciones: A-2 herramienta de acero, en el blanco. Incluye resorte de repuesto. Se adapta a las pistolas Ruger MKII, MKIII, MKIV y 22/45; 10/22® y 10/22® Magnum.

Más...

Evaluaciones de clientes para VOLQUARTSEN EXACT EDGE EXTRACTOR

Número de evaluaciones: 12
De brownells.com: 12
Evaluación media: 5

Works GREAT in Ruger auto pistols too ! (25/10/2009)

Volquartsen Is Good Medicine! (24/08/2010)

No more stuck shells. (22/01/2012)

This was easy to install and after testing it I have yet to have another failure to extract.

Extractor (10/02/2013)

A lot sharper and more surface area over the Factory Ruger extractor. More consistent ejection and jams are now non existent.

Broken to improved with one little part (15/03/2013)

THIS IS THE FIX (18/02/2014)

Easy Install & Works Great (12/04/2014)

Perfect (13/07/2015)

Could be A MIRACLE! (25/10/2015)

PERFECT (25/06/2016)

Flawless (21/04/2017)

No Malfunctions During Last Outing! (17/07/2018)

Leer 12 mas calificaciones en brownells.com

Los clientes compraron
Alternativas

Sale

Millenium Custom Ii FITS 9X19, 9X21, 9X23X 38 SUPER COMP.
1911 ADVANCED COMPETITION EXTRACTOR

Millenium Custom Ii

No disponible

Extractors

4,4

Pachmayr MODEL CD/C COLT "D" FRAME
COMPAC GRIPS

Pachmayr

En stock Plazo de entrega de aproximadamente 14-21 días.
4 pcs. en el almacén de EE.UU.

59,90 € *

Grips

4,3

WILSON COMBAT BLUED EZ-LOADER
1911 EZ-LOADER MAGWELL

WILSON COMBAT

En stock Plazo de entrega de aproximadamente 14-21 días.
3 pcs. en el almacén de EE.UU.

54,90 € * 54,90 € - 59,90 €*

Mainspring Housings

4,1

Sale

POWER CUSTOM PRE-TRAVEL ADJUSTABLE 10/22® HAMMER & SEAR KIT
RUGER® 10/22® PRE-TRAVEL ADJUSTABLE HAMMER & SEAR KIT

POWER CUSTOM

Reordenado Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.

119,90 € * 64,90 € - 119,90 €*

(Seleccione los artículos en venta!)

Precio anterior 128,93 €

Performance Upgrade Kits

3,8

Sale

TTI INTL BOLT CATCH PIN
GAS TUBE PIN

TTI INTL

Reordenado Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.

9,90 € * 8,90 € - 9,90 €*

(Seleccione los artículos en venta!)

Precio anterior 15,80 €

Trigger Guard Pins | Pasadores del estractor

Identificarse

¿Ha olvidado su contraseña?
Registrarse

Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.

Redes Sociales

Navegacion

Categorias

Ordering

Servicio al cliente

¡Bienvenido!

Bienvenido a Brownells, la principal Armeria de accesorios de armas de fuego, piezas de armas y herramientas para armeros en España. En nuestra web podrá encontrar todo tipo de accesorios y repuestos para sus rifles, carabinas, escopetas o armas cortas. Si le gusta la caza o el tiro de precisión esta es su web.

La promesa de Brownells España

La promesa Brownells para nuestros clientes: TU SATISFACIÓN ESTÁ GARANTIZADA. Si por cualquier motivo no estás 100% satisfecho con cualquiera de los productos comprados a nosotros, se lo devolvemos o cambiamos.

Nuestra oferta

Si te gusta disparar, trabajar con armas como negocio o hobby, o simplemente poseer un arma, este es tu lugar. Durante más de 75 años, tiradores, armeros profesionales, aficionados, cuerpos de defensa y especialistas en armas han venido a Brownells.es por la alta calidad en sus piezas de armas y en los repuestos que ellos necesitan.

Encontrarás más de 90,000 incluyendo exclusivas piezas de armas, accesorios, herramientas para armeros, munición y otros productos para el manteniminto, reparación y mejora de tus pistolas.

Su equipo Brownells España

Armeria A. Izquierdo (B-13309356)