The Strike Industries Aluminum Extended Magazine Plate for GLOCK™ G19 (9mm) was designed to provide smoother magazine reloading through a slow drag / no snag design while maintaining maximum magazine capacity. Machined from 6061-T6 aluminum, this Extended Magazine Plate (EMP) adds plus 5 9mm rounds to OEM double stack GLOCK™ G19 magazines. Following the success of our EMP systems for pistols, the form factor and unique geometric design gives a unified and aggressive aesthetic look to your GLOCK™ G19. Included is an aluminum plate which adds extra locking security. Give your GLOCK™ pistol the extra rounds it deserves with the Strike Industries Aluminum Extended Magazine Plate (EMP) for GLOCK™ G19 (9mm). WARNING: DO NOT OVERTIGHTEN set screw when installing the aluminum locking plate. If you are unsure, please contact our customer support team or consult with your local gunsmith. Package Contents: x1 Aluminum Extended Magazine Plate for GLOCK™ G19 x1 Extended length spring x1 Aluminum locking plate x1 Aluminum locking plate set screw (M3x8mm) x1 Hex tool x1 Warning card Product Features: Machined from 6061-T6 aluminum Plus 5 round capacity for 9mm Includes aluminum locking plate Low drag / no snag design Fits USPSA 140mm race division limit Available in anodized SI BLACKLINE, REDLINE or FDELINE colors COMPATIBILITY: GLOCK™ factory OEM G19 (9mm) double stack magazines SI EMP Pocket Clip Magwell: tested to work with SI magwells NOT COMPATIBLE: G23 (.40 Cal) 10-round magazines ETS Magazines NOTE: Not for sale to California, Hawaii, New York and New Jersey residents due to 10-round state laws. The checkout process will show NO shipping method available. It is the responsibility of the customer to know and abide with local gun laws. DISCLAIMER: Due to numerous factors that take place during the anodization process, the color lines from batch to batch of a certain product may vary Threaded holes located on EMP are anodizing blind holes and may not be completely covered with coating WARNING: DO NOT OVERTIGHTEN set screw when installing the aluminum locking plate. If you are unsure, please contact our customer support team or consult with your local gunsmith. SI aluminum EMP was intentionally designed to be a tight fit and can damage the polymer magazine body base ears. Must be installed by a certified gunsmith only. Use of small c-clamp (or similar tool) to gently and lightly squeeze the bottom middle of the magazine body just above the plastic locking ears where the SI aluminum EMP attaches to the magazine. Just enough so the SI aluminum EMP will slide in or out. Be careful not to bend the OEM magazine body metal liner and remove the c-clamp (or similar tool) as soon as the SI aluminum EMP is installed or removed. C-clamp or similar tool may mar/scratch magazine body surface. Please be careful and use a material to protect the magazine body surface. DISCLAIMER: -This product is not manufactured, authorized, endorsed, or warranted by GLOCK. GLOCK does not warrant or represent that this product is compatible with GLOCK pistols. --“GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. and GLOCK Ges.m.b.H. Neither Strike Industries Inc. nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK pistols, parts, or components. -CALIFORNIA PROPOSITION 65 WARNING:- WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov
Mejora tu GLOCK® G19 con el Plato Extendido de Aluminio de Strike Industries
El Plato Extendido de Aluminio para GLOCK™ G19 (9mm) de Strike Industries ha sido diseñado para proporcionar una recarga de cargador más suave gracias a su diseño de arrastre lento / sin enganches, manteniendo al mismo tiempo la máxima capacidad del cargador.
Descripción del Producto
Fabricado en aluminio 6061-T6, este Plato Extendido de Cargador (EMP) añade 5 rondas adicionales de 9mm a los cargadores de doble pila OEM de GLOCK™ G19. Siguiendo el éxito de nuestros sistemas EMP para pistolas, el factor de forma y el diseño geométrico único le dan una estética unificada y agresiva a tu GLOCK™ G19. Se incluye un plato de aluminio que añade seguridad adicional al bloqueo.
Proporciona a tu pistola GLOCK™ las rondas extra que merece con el Plato Extendido de Aluminio (EMP) para GLOCK™ G19 (9mm).
Contenido del Paquete:
- x1 Plato Extendido de Aluminio para GLOCK™ G19
- x1 Resorte de longitud extendida
- x1 Plato de bloqueo de aluminio
- x1 Tornillo de bloqueo de aluminio (M3x8mm)
- x1 Herramienta hexagonal
- x1 Tarjeta de advertencia
Características del Producto:
- Fabricado en aluminio 6061-T6
- Capacidad adicional de 5 rondas para 9mm
- Incluye plato de bloqueo de aluminio
- Diseño de bajo arrastre / sin enganches
- Se ajusta al límite de 140mm de la división de carreras USPSA
- Disponible en colores anodizados SI BLACKLINE, REDLINE o FDELINE
Compatibilidad:
- Cargadores de doble pila OEM GLOCK™ G19 (9mm)
- Clip para bolsillo SI EMP
- Magwell: probado para funcionar con magwells SI
No Compatible Con:
- G23 (.40 Cal)
- Cargadores de 10 rondas
- Cargadores ETS
Nota: No disponible para la venta a residentes de California, Hawái, Nueva York y Nueva Jersey debido a las leyes estatales de 10 rondas. El proceso de pago mostrará que NO hay método de envío disponible. Es responsabilidad del cliente conocer y cumplir con las leyes locales de armas.
Descargo de Responsabilidad: Debido a numerosos factores que ocurren durante el proceso de anodización, las líneas de color de un lote a otro de un cierto producto pueden variar. Los orificios roscados ubicados en el EMP son agujeros ciegos de anodización y pueden no estar completamente cubiertos con recubrimiento.
ADVERTENCIA: NO APRIETES EN EXCESO el tornillo de ajuste al instalar el plato de bloqueo de aluminio. Si no estás seguro, contacta a nuestro equipo de soporte al cliente o consulta con tu armero local. El SI aluminum EMP fue diseñado intencionalmente para un ajuste ceñido y puede dañar las orejas de la base del cuerpo del cargador de polímero. Debe ser instalado solo por un armero certificado.
Utiliza un pequeño c-clamp (o herramienta similar) para presionar suavemente el medio inferior del cuerpo del cargador justo por encima de las orejas de bloqueo de plástico donde se conecta el SI aluminum EMP al cargador. Solo lo suficiente para que el SI aluminum EMP se deslice hacia dentro o hacia fuera. Ten cuidado de no doblar el revestimiento metálico del cuerpo del cargador OEM y retira el c-clamp (o herramienta similar) tan pronto como el SI aluminum EMP esté instalado o retirado. El c-clamp o herramienta similar puede rayar la superficie del cuerpo del cargador. Por favor, ten cuidado y utiliza un material para proteger la superficie del cuerpo del cargador.
Descargo de Responsabilidad: Este producto no es fabricado, autorizado, respaldado ni garantizado por GLOCK. GLOCK no garantiza ni representa que este producto sea compatible con las pistolas GLOCK. "GLOCK" es una marca registrada federalmente de GLOCK, Inc. y es una de las muchas marcas propiedad de GLOCK, Inc. y GLOCK Ges.m.b.H. Ni Strike Industries Inc. ni este sitio están afiliados de ninguna manera, ni son respaldados por GLOCK, Inc. o GLOCK Ges.m.b.H. El uso de "GLOCK" en esta página es meramente para publicitar la venta de pistolas, partes o componentes GLOCK.
ADVERTENCIA DE LA PROPUESTA 65 DE CALIFORNIA: Este producto contiene químicos que el Estado de California conoce que causan cáncer y defectos de nacimiento u otros daños reproductivos. Para más información: www.P65Warnings.ca.gov