Brownells Iberica - El mayor proveedor de accesorios para el Tiro, Piezas y herramientas del armero. España
680665827220 100044421
RBF (Reinforced Buffer retainer, Forward Controls) is a strengthened AR buffer retainer machined with Swiss machines from 17-4 stainless steel bar stock, and heat treated to H900 hardness.  RBF features a reinforced tip that is 10% larger (0.102) than TDP spec (0.093).  FCD didn’t want RBF to be timed (as the case with a rectangular tip), so RBF retains the TDP buffer retainer's versatile round tip and is installed per TM instructions.  10% is as much as we could increase before encountering receiver extension timing incompatibilities. RBF is compatible with AR15/M16 mil-spec rifle and carbine receiver extensions, as well as Vltor A5 system receiver extensions. 17-4 stainless steel Heat treated AR15 and 308 AR compatible buffer retainer 10% larger diameter tip NOTE: Always wear eye protection while handling springs under pressure, spring loaded pins and detents. RBF isn't a fix for out of spec lowers with incorrectly positioned buffer retainer hole.  If you detect excessive wear marks on the buffer's front face, it's advisable to warranty exchange your lower receiver. Receiver extensions (REs) timing on the receiver can vary.  While the an RE can rotate past dead center (with the RE covering and retaining the buffer retainer) by 45 degrees or more on one receiver, it might only be able to do 15 degrees or less on another.  Also, different REs have different timing values.
17.9 17.9 1 EUR
New
N.º de producto: 100044421
FORWARD CONTROLS DESIGN AR-15 BUFFER RETAINER STAINLESS STEEL
Ref Fabricante: RBFREINFORCED 680665827220 El RBF (Retenedor de Buffer Reforzado, de Forward Controls) es un retenedor de buffer AR fortalecido, mecanizado con máquinas suizas a partir de barra de acero inoxidable 17-4 y tratado térmicamente hasta alcanzar una dureza H900. El RBF presenta una punta reforzada que es un 10% más grande (0.102) que la especificación TDP (0.093). FCD no quería que el RBF tuviera que ser sincronizado (como es el caso con una punta rectangular), así que el RBF mantiene la punta redonda versátil del retenedor de buffer de la especificación TDP y se instala siguiendo las instrucciones del TM. El 10% es el máximo que pudimos aumentar antes de encontrar incompatibilidades de sincronización con la extensión del receptor. El RBF es compatible con las extensiones de receptor de rifles y carabinas AR15/M16 mil-spec, así como con las extensiones de receptor del sistema Vltor A5. Acero inoxidable 17-4 Tratado térmicamente Compatible con retenedor de buffer AR15 y 308 AR Punta de diámetro un 10% mayor NOTA: Siempre usa protección ocular al manejar muelles bajo presión, pasadores y detentes cargados por muelle. El RBF no es una solución para lowers fuera de especificación con un agujero para el retenedor de buffer posicionado incorrectamente. Si detectas marcas de desgaste excesivo en la cara frontal del buffer, es recomendable que solicites un cambio de garantía de tu lower receiver. La sincronización de las extensiones de receptor (REs) en el receptor puede variar. Mientras que una RE puede rotar más allá del punto muerto (con la RE cubriendo y reteniendo el retenedor de buffer) en 45 grados o más en un receptor, podría ser capaz de hacer solo 15 grados o menos en otro. Además, diferentes REs tienen diferentes valores de sincronización.
17.9 EUR 59 17,90 € *
Plazo de entrega de aproximadamente 14-21 días.
Más de 10 pcs. en almacén de EE.UU.
Caracteristicas: Hacer: AR-15

Atributos

Hacer: AR-15 Peso de entrega: 0,005kg Altura de envío: 13mm Ancho de envío: 102mm Longitud de envío: 178mm

Detalles del artículo

Hecho en USA
Clasificación de exportación de EE. UU.: 0A501.x



RBF (Reinforced Buffer retainer, Forward Controls) is a strengthened AR buffer retainer machined with Swiss machines from 17-4 stainless steel bar stock, and heat treated to H900 hardness.  RBF features a reinforced tip that is 10% larger (0.102) than TDP spec (0.093).  FCD didn’t want RBF to be timed (as the case with a rectangular tip), so RBF retains the TDP buffer retainer's versatile round tip and is installed per TM instructions.  10% is as much as we could increase before encountering receiver extension timing incompatibilities. RBF is compatible with AR15/M16 mil-spec rifle and carbine receiver extensions, as well as Vltor A5 system receiver extensions. 17-4 stainless steel Heat treated AR15 and 308 AR compatible buffer retainer 10% larger diameter tip NOTE: Always wear eye protection while handling springs under pressure, spring loaded pins and detents. RBF isn't a fix for out of spec lowers with incorrectly positioned buffer retainer hole.  If you detect excessive wear marks on the buffer's front face, it's advisable to warranty exchange your lower receiver. Receiver extensions (REs) timing on the receiver can vary.  While the an RE can rotate past dead center (with the RE covering and retaining the buffer retainer) by 45 degrees or more on one receiver, it might only be able to do 15 degrees or less on another.  Also, different REs have different timing values.
Newsletters