Accurate performance from your ammunition is absolutely dependent on uniformity of both the bullet and the case. Achieving that uniformity is not possible without an accurate, reliable measuring device. The Forster exclusive Co-Ax Case & Cartridge Inspector provides you with the ability to ensure uniformity by measuring three critical dimensions: neck wall thickness, case neck concentricity, and bullet runout. Measurements are in increments of one-thousandth of an inch so accuracy is superb. The Inspector is unique because it checks both the bullet and case alignment in relation to the centerline (axis) of the entire cartridge or case. The Forster Case Inspector uses Forster Case Trimmer Pilots (sold separately).
Más...
El rendimiento preciso de tu munición depende absolutamente de la uniformidad tanto de la bala como de la vaina. Lograr esa uniformidad no es posible sin un dispositivo de medición preciso y confiable. El exclusivo Inspector de Vainas y Cartuchos Co-Ax de Forster te proporciona la capacidad de asegurar la uniformidad midiendo tres dimensiones críticas: el grosor de la pared del cuello, la concentricidad del cuello de la vaina y la desviación de la bala. Las mediciones se realizan en incrementos de una milésima de pulgada, por lo que la precisión es excelente. El Inspector es único porque verifica tanto la alineación de la bala como de la vaina en relación con la línea central (eje) de todo el cartucho o vaina. El Inspector de Vainas de Forster utiliza Pilotos para Recortadora de Vainas de Forster (se venden por separado).
Más...
Evaluaciones de clientes para FORSTER PRODUCTS, INC. CO-AX CASE AND CARTRIDGE INSPECTOR
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3
So so tool(28/09/2013)
The v groove holder the bullet sits in was very rough from the factory. So much so that within a few turns it was cutting the copper on the bullet. little time with a dremmel and a stone and polish wheel cleaned it up glass smooth and the problem is gone. It takes a little bit to get the tool setup right so all the angles jive but once done it seems to work pretty well. One thing to note though is if the meplat is not perfect you will not get a good measurement. There is a spring that pushes the round against an anvil where the v groove piece above is. This causes the round to wobble a little giving inaccurate measurements if you are not careful. Need to put a little sizing wax on the rear v section where the case rolls to make it smooth. Overall it works well once you take the time to properly adjust everything but is definitely not a tool for the impatient!
Useful(11/09/2017)
I agree with the above review about the difficulty of set up and the V groove. The tool is tedious to setup, and when you change over from checking concentricity to checking T.I.R. it again takes time to get all the adjustments made. It isn't the most efficient process and the tool really can't handle a long cartridge witout the case head compression spring pushing the meplat into the adjustment bar, though it is very useful for checking case neck thickness. I'm not a competitive shooter where I need every little bit of accuracy, but I do like to build very consistent rounds. Knowing what I do now I would have purchased the Sinclair concentricity guage instead
N.º de producto: 749007261 FORSTER PRODUCTS, INC. CO-AX CASE AND CARTRIDGE INSPECTOR Ref Fabricante: 010482757253718014 El rendimiento preciso de tu munición depende absolutamente de la uniformidad tanto de la bala como de la vaina. Lograr esa uniformidad no es posible sin un dispositivo de medición preciso y confiable. El exclusivo Inspector de Vainas y Cartuchos Co-Ax de Forster te proporciona la capacidad de asegurar la uniformidad midiendo tres dimensiones críticas: el grosor de la pared del cuello, la concentricidad del cuello de la vaina y la desviación de la bala. Las mediciones se realizan en incrementos de una milésima de pulgada, por lo que la precisión es excelente. El Inspector es único porque verifica tanto la alineación de la bala como de la vaina en relación con la línea central (eje) de todo el cartucho o vaina. El Inspector de Vainas de Forster utiliza Pilotos para Recortadora de Vainas de Forster (se venden por separado).
174.9EUR1174,90 €
*
Plazo de entrega de aproximadamente 14-21 días. 1 pcs. en el almacén de EE.UU.
Accurate performance from your ammunition is absolutely dependent on uniformity of both the bullet and the case. Achieving that uniformity is not possible without an accurate, reliable measuring device. The Forster exclusive Co-Ax Case & Cartridge Inspector provides you with the ability to ensure uniformity by measuring three critical dimensions: neck wall thickness, case neck concentricity, and bullet runout. Measurements are in increments of one-thousandth of an inch so accuracy is superb. The Inspector is unique because it checks both the bullet and case alignment in relation to the centerline (axis) of the entire cartridge or case. The Forster Case Inspector uses Forster Case Trimmer Pilots (sold separately).
Más...
El rendimiento preciso de tu munición depende absolutamente de la uniformidad tanto de la bala como de la vaina. Lograr esa uniformidad no es posible sin un dispositivo de medición preciso y confiable. El exclusivo Inspector de Vainas y Cartuchos Co-Ax de Forster te proporciona la capacidad de asegurar la uniformidad midiendo tres dimensiones críticas: el grosor de la pared del cuello, la concentricidad del cuello de la vaina y la desviación de la bala. Las mediciones se realizan en incrementos de una milésima de pulgada, por lo que la precisión es excelente. El Inspector es único porque verifica tanto la alineación de la bala como de la vaina en relación con la línea central (eje) de todo el cartucho o vaina. El Inspector de Vainas de Forster utiliza Pilotos para Recortadora de Vainas de Forster (se venden por separado).
Más...
Evaluaciones de clientes para FORSTER PRODUCTS, INC. CO-AX CASE AND CARTRIDGE INSPECTOR
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3
So so tool(28/09/2013)
The v groove holder the bullet sits in was very rough from the factory. So much so that within a few turns it was cutting the copper on the bullet. little time with a dremmel and a stone and polish wheel cleaned it up glass smooth and the problem is gone. It takes a little bit to get the tool setup right so all the angles jive but once done it seems to work pretty well. One thing to note though is if the meplat is not perfect you will not get a good measurement. There is a spring that pushes the round against an anvil where the v groove piece above is. This causes the round to wobble a little giving inaccurate measurements if you are not careful. Need to put a little sizing wax on the rear v section where the case rolls to make it smooth. Overall it works well once you take the time to properly adjust everything but is definitely not a tool for the impatient!
Useful(11/09/2017)
I agree with the above review about the difficulty of set up and the V groove. The tool is tedious to setup, and when you change over from checking concentricity to checking T.I.R. it again takes time to get all the adjustments made. It isn't the most efficient process and the tool really can't handle a long cartridge witout the case head compression spring pushing the meplat into the adjustment bar, though it is very useful for checking case neck thickness. I'm not a competitive shooter where I need every little bit of accuracy, but I do like to build very consistent rounds. Knowing what I do now I would have purchased the Sinclair concentricity guage instead
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.