Reduces Pull Weight For A Light, Crisp Trigger Pull
Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.
SPECS: Spring steel. #25A includes (3) springs. #25B include (2) springs.
Más...
Reduce el Peso del Disparador para un Disparo Suave y Preciso
Los kits de resortes para reducir el peso del disparador de competición disminuyen el peso del disparador pesado de fábrica en aproximadamente 2½ libras, logrando así un disparador mucho más suave y una mejor precisión. El #25A es compatible con todas las pistolas Browning Hi-Power anteriores a 1991, e incluye (1) resorte de martillo de 22 lb., (1) resorte de retorno del disparador de potencia reducida y (1) resorte del percutor de potencia reducida. El #25B es compatible con las pistolas Hi-Power de 1991 en adelante, e incluye (1) resorte de martillo de 22 lb. y (1) resorte del percutor de potencia reducida.
ESPECIFICACIONES: Acero para resortes. El #25A incluye (3) resortes. El #25B incluye (2) resortes.
Más...
Evaluaciones de clientes para CYLINDER & SLIDE #25-B SPRING KIT
Número de evaluaciones: 4
De brownells.com: 4
Evaluación media: 3,3
Misleading(31/05/2012)
I installed these springs on a new BHP MK3 which originally measured 9.25 lbs at the trigger. After installation the trigger measured 9.25 lbs. The hammer spring was 4 coils longer than the stock or another manutacturer's replacement springs. This means you either have to cut the coils or pre-load the spring extensively to install it on the strut. So unless your hammer / sear interface angle is positive or neutral with really rough surfaces these parts will do little to help the trigger pull. Modifications to the sear spring pressure will however produce changes in the trigger pull weight.
It work !!(25/01/2010)
I just installed the 3 springs in my 1973 BHP the job it self require some smithing ability , some roll pin in the trigger group are hard to punch out. The Hammer spring is also tricky to replace. The easiest part is the firing pin spring. My High power lost is rock hard trigger and now has a much more manageable trigger pull. while I was there I also removed the Mag release safety spring. which also help the trigger pull. Good luck
excellent(01/10/2011)
great spring set, works really well to improve trigger pull and still reliable.
BUT the hammer spring is a bit of a pain to replace (no fault of this set, just be aware) so allow some time or get some advice.
Decent kit, but there were some problems(08/04/2013)
Decided to replace the springs with lighter ones along with a trigger job on the old Hi-power. Installation was a breeze, and everything was good until I reassembled the gun and it would not function correctly. The hammer was binding. Took it all apart and found the replacement spring for the hammer was about 1/4" longer than the original and was fully compressed and binding before the hammer was fully cocked. Ended up having to cut the spring down to get it to the correct length. After that everything functions fine. The kit I ordered was part no. 206-025-001 for the pre-91 Hi-power, as my Hi-power is a 1973. Maybe I got the spring from a later Hi-power by mistake? Not too sure.
N.º de producto: 206025002 CYLINDER & SLIDE #25-B SPRING KIT Ref Fabricante: CS0025B000000000253 Los kits de resortes para reducir el peso del disparador de competición disminuyen el peso del disparador pesado de fábrica en aproximadamente 2½ libras, logrando así un disparador mucho más suave y una mejor precisión. El #25A es compatible con todas las pistolas Browning Hi-Power anteriores a 1991, e incluye (1) resorte de martillo de 22 lb., (1) resorte de retorno del disparador de potencia reducida y (1) resorte del percutor de potencia reducida. El #25B es compatible con las pistolas Hi-Power de 1991 en adelante, e incluye (1) resorte de martillo de 22 lb. y (1) resorte del percutor de potencia reducida.
El kit #25B es compatible con pistolas Hi-Power de 1991 en adelante e incluye un resorte de martillo de 22 lb. y un resorte del percutor de potencia reducida.
Los kits reducen el peso del disparador en aproximadamente 2½ libras, mejorando la suavidad y precisión del disparo.
El kit está fabricado con acero para resortes y pertenece a la categoría de Performance Enhancing Kits.
Atributos
Peso de entrega: 0,009kgAncho de envío: 83mmLongitud de envío: 146mm
UPC
: 000000000253
Detalles del artículo
Hecho en USA
N.º de producto: 206025001 CYLINDER & SLIDE #25-A SPRING KIT Ref Fabricante: CS0025A000000002516 Los kits de resortes para reducir el peso del disparador de competición disminuyen el peso del disparador pesado de fábrica en aproximadamente 2½ libras, logrando así un disparador mucho más suave y una mejor precisión. El #25A es compatible con todas las pistolas Browning Hi-Power anteriores a 1991, e incluye (1) resorte de martillo de 22 lb., (1) resorte de retorno del disparador de potencia reducida y (1) resorte del percutor de potencia reducida. El #25B es compatible con las pistolas Hi-Power de 1991 en adelante, e incluye (1) resorte de martillo de 22 lb. y (1) resorte del percutor de potencia reducida.
43.9EUR043,90 €
*
Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.
Reduces Pull Weight For A Light, Crisp Trigger Pull
Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.
SPECS: Spring steel. #25A includes (3) springs. #25B include (2) springs.
Más...
Reduce el Peso del Disparador para un Disparo Suave y Preciso
Los kits de resortes para reducir el peso del disparador de competición disminuyen el peso del disparador pesado de fábrica en aproximadamente 2½ libras, logrando así un disparador mucho más suave y una mejor precisión. El #25A es compatible con todas las pistolas Browning Hi-Power anteriores a 1991, e incluye (1) resorte de martillo de 22 lb., (1) resorte de retorno del disparador de potencia reducida y (1) resorte del percutor de potencia reducida. El #25B es compatible con las pistolas Hi-Power de 1991 en adelante, e incluye (1) resorte de martillo de 22 lb. y (1) resorte del percutor de potencia reducida.
ESPECIFICACIONES: Acero para resortes. El #25A incluye (3) resortes. El #25B incluye (2) resortes.
Más...
Evaluaciones de clientes para CYLINDER & SLIDE #25-B SPRING KIT
Número de evaluaciones: 4
De brownells.com: 4
Evaluación media: 3,3
Misleading(31/05/2012)
I installed these springs on a new BHP MK3 which originally measured 9.25 lbs at the trigger. After installation the trigger measured 9.25 lbs. The hammer spring was 4 coils longer than the stock or another manutacturer's replacement springs. This means you either have to cut the coils or pre-load the spring extensively to install it on the strut. So unless your hammer / sear interface angle is positive or neutral with really rough surfaces these parts will do little to help the trigger pull. Modifications to the sear spring pressure will however produce changes in the trigger pull weight.
It work !!(25/01/2010)
I just installed the 3 springs in my 1973 BHP the job it self require some smithing ability , some roll pin in the trigger group are hard to punch out. The Hammer spring is also tricky to replace. The easiest part is the firing pin spring. My High power lost is rock hard trigger and now has a much more manageable trigger pull. while I was there I also removed the Mag release safety spring. which also help the trigger pull. Good luck
excellent(01/10/2011)
great spring set, works really well to improve trigger pull and still reliable.
BUT the hammer spring is a bit of a pain to replace (no fault of this set, just be aware) so allow some time or get some advice.
Decent kit, but there were some problems(08/04/2013)
Decided to replace the springs with lighter ones along with a trigger job on the old Hi-power. Installation was a breeze, and everything was good until I reassembled the gun and it would not function correctly. The hammer was binding. Took it all apart and found the replacement spring for the hammer was about 1/4" longer than the original and was fully compressed and binding before the hammer was fully cocked. Ended up having to cut the spring down to get it to the correct length. After that everything functions fine. The kit I ordered was part no. 206-025-001 for the pre-91 Hi-power, as my Hi-power is a 1973. Maybe I got the spring from a later Hi-power by mistake? Not too sure.