Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.604" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Mejora tu CZ SHADOW 2 con el soporte de mira LEUPOLD DELTAPOINT PRO
El soporte de mira CZ SHADOW 2 LEUPOLD DELTAPOINT PRO de EGW es la solución perfecta para montar tu punto rojo de manera sencilla y efectiva.
Descripción del Producto
- Material: Aluminio 7075
- Acabado: Matte Black Hardcoat
- Longitud Total: 1.604"
- Anchura Total: .99"
- Hardware de Montaje:
- (2) Tornillos de Cabeza de Botón 6-32
- (2) Tornillos de Cabeza Plana 6-32
- (1) Tornillo de Ajuste 6-32
- Compatibilidad con Puntos Rojos:
Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter
Los puntos rojos de EGW están diseñados para instalarse de izquierda a derecha (con la boca del cañón hacia adelante). La guía tiene un perfil progresivo que facilita la instalación.
Simplemente retira la mira trasera de tu arma y reemplázala con nuestro soporte para montar tu Vortex Viper/Venom, Burris FastFire o Docter. No se requieren modificaciones. Puedes quitar nuestro soporte y volver a colocar tu mira trasera en cualquier momento. Hardware de montaje incluido.
Instrucciones de Instalación
- Retira la mira trasera*
- Instala el Soporte de Mira EGW en la guía
- Ajusta el tornillo de ajuste (si aplica)
- Coloca el punto rojo en el Soporte de Mira EGW (colocar un pequeño trozo de papel entre el punto rojo y el soporte facilitará la extracción y mantendrá el Loctite alejado del punto rojo).
- Aplica Loctite azul a los tornillos de montaje proporcionados
- Ajusta los tornillos de montaje a 15 in/lbs
Nota: Los tornillos incluidos con este soporte requieren una llave allen de 5/64'' para la instalación.