Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Mejora tu puntería con el soporte CZ SHADOW 2 VORTEX VIPER/VENOM.
El soporte para miras rojas CZ SHADOW 2 VORTEX VIPER/VENOM de EGW es la solución perfecta para montar tu mira de punto rojo de manera sencilla y efectiva.
Descripción del Producto
- Material: 7075 Aluminum
- Recubrimiento: Matte Black Hardcoat
- Longitud Total: 1.811"
- Anchura Total: .99"
- Hardware de Montaje:
- (2) Tornillos de Cabeza de Botón 6-32
- (2) Tornillos de Cabeza Plana 6-32
- (1) Tornillo de Ajuste 6-32
- Ajuste de Punto Rojo: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter
Las miras rojas de EGW están diseñadas para ser instaladas de izquierda a derecha (con el cañón apuntando hacia adelante). La cola de milano tiene un ángulo progresivo para facilitar la instalación. Simplemente quita la mira trasera de tu arma y reemplázala con nuestro soporte para montar tu Vortex Viper/Venom, Burris FastFire o mira de punto rojo Docter. No se requieren alteraciones. Puedes quitar nuestro soporte y volver a colocar tu mira trasera en cualquier momento. Hardware de montaje incluido.
Instrucciones de Instalación
- Quita la mira trasera*
- Instala el Soporte EGW en la cola de milano
- Ajusta el tornillo de ajuste (si es aplicable)
- Coloca la mira de punto rojo en el Soporte EGW (colocar un pequeño trozo de papel entre la mira de punto rojo y el soporte facilitará la extracción y mantendrá el Loctite alejado de la mira de punto rojo).
- Aplica Loctite azul a los tornillos de montaje proporcionados
- Ajusta los tornillos de montaje a 15in/lbs
2 Tornillos de Cabeza de Botón: Proporcionados para las miras Vortex Viper y Venom.
2 Tornillos de Cabeza Plana: Proporcionados para las miras Burris FastFire y Docter.
Los tornillos incluidos con este soporte requieren una llave Allen de 5/64'' para la instalación.