This mount is NOT a drop in part and will require fitting. EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. EGW products should be installed and checked by a qualified and competent gunsmith. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail after checking for fit Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Firearms with oversized Novak cut dovetails. This mount is made .007"" larger than a standard Novak cut and will require fitting.
Montura Oversized Novak para Vortex Viper/Venom: ¡Instalación precisa y fácil!
Esta montura NO es una pieza de instalación directa y requerirá ajuste. Las miras de punto rojo EGW están diseñadas para ser instaladas de izquierda a derecha (con el cañón apuntando hacia adelante). La dovetail tiene un ángulo progresivo para facilitar la instalación.
Simplemente quita la mira trasera de tu arma y reemplázala con la montura EGW para montar tu Vortex Viper/Venom, Burris FastFire o Docter. Puedes quitar la montura y volver a colocar tu mira trasera en cualquier momento. Hardware de montaje incluido. Los productos EGW deben ser instalados y revisados por un armero calificado y competente.
Instrucciones de Instalación
- Quita la mira trasera*
- Instala la Montura EGW en la dovetail después de verificar el ajuste
- Ajusta el tornillo de fijación (si aplica)
- Coloca la mira de punto rojo sobre la Montura EGW (colocar un pequeño trozo de papel entre la mira de punto rojo y la montura facilitará la extracción y mantendrá el Loctite alejado de la mira de punto rojo).
- Aplica Loctite azul a los tornillos de montaje proporcionados
- Ajusta los tornillos de montaje a 15in/lbs
Incluye:
- 2 Tornillos de Cabeza de Botón - Proporcionados para las miras Vortex Viper y Venom
- 2 Tornillos de Cabeza Plana - Proporcionados para las miras Burris FastFire y Docter
Los tornillos incluidos con esta montura requieren una llave allen de 5/64'' para la instalación. La modificación de tu arma puede anular la garantía del fabricante.
Este producto debe ser instalado y revisado por un armero calificado. No se expresa ni se implica ninguna responsabilidad por daños o lesiones que puedan resultar de una instalación o uso inadecuado de este producto.
Esta montura es compatible con:
Armas de fuego con dovetails Novak de tamaño grande. Esta montura es .007" más grande que una Novak estándar y requerirá ajuste.