CN5F (Castle Nut, A5, Forward Controls) is an extended version of CNF Forward Controls Design (FCD) have been making since 2018. CN5F is designed specifically for the superb Vltor A5 system, CN5F is 0.1" longer, and is as long as FCD can make a castle nut while ensuring backward compatibility, and the stock's ability to fully collapse on Vltor's RE-A5 and FCD's RE5F. Note: not all stocks will fully collapse on A5 compatible REs. For more information on the differences between RE-A5, RE5F and RE10/A5SR, please follow this link: https://www.forwardcontrolsdesign.com/Vltor-RE-A5-vs-RE10-A5SR_ep_78-1.html CN5F aims to cover as much of the threaded area of a receiver extension (RE) as possible. It could be made longer, but it will run into backward compatibility issues with some REs' timing when installing the castle nut and end plate on the RE. CN5F is made specifically for the Vltor A5 system, and it will allow even the longest carbine stocks to fully collapse on RE-A5 and FCD's RE5F. While CN5F will also work on standard TDP spec length RE, the additional length of the castle nut will prevent the carbine stock to fully collapse. Other than its length, CN5F shares common features with its smaller brother, CNF. The TDP spec castle nut is a simple and robust fastener that is almost perfect for the job it's tasked to perform. Over the years, FCD have consistently come up with two minor gripes, first is its staking notches seem rather shallow and short, second is FCD don't enjoy using the castle nut's wrench notches as serrations (FCD's fingers invariably find their way to these sharp cutouts) to rotate it towards to the end plate while installing it. CN5F (Castle Nut, Forward Controls) is based on the TDP spec castle nut, with couple of changes: 0.1" longer. Staking notches angle changed from 45 to 30 degrees, this results in longer (25% longer than TDP spec) and deeper notches than found on TDP castle nuts. Number of staking notches increased from 3 to 4, spaced equally on the CNF. The castle nut is to be staked in two places, FCD are not advocating staking in more than two places, CNF's 4 staking notches mean that, at all times, 3 will be visible and available for staking, it simply gives the user more staking location options. Coarse serrations on the wrench side of the nut, a single use feature to make it easier while rotating the CNF towards the end plate. It is FCD’s opinion that a castle nut should be staked per TM, CNF's and CN5F's longer and deeper notch reinforces the belief, that once installed and staked, it will not loosen without the user's deliberate action. Forward Controls Design like the idea of quick detach, but some things on an AR are meant to stay put, and considerable effort was made to ensure that by the original designers. CNF and CN5F are a continuation and evolution in that direction. CN5F is billet machined in 4140 PH steel, and black nitrided (Cerakoted FDE, OD green, and burnt bronze also available). As with everything Forward Controls Design produces, it is proudly made in the USA. Weight: 0.51oz Material: 4140 PH Made in USA
¡Descubre el A5 CASTLE NUT de FORWARD CONTROLS DESIGN!
El CN5F (Castle Nut, A5, Forward Controls) es una versión extendida del CNF que Forward Controls Design (FCD) ha estado fabricando desde 2018. Diseñado específicamente para el excepcional sistema Vltor A5, el CN5F es 0.1" más largo y es lo más largo que FCD puede hacer en un castle nut, asegurando la compatibilidad hacia atrás y la capacidad del stock para colapsar completamente en el RE-A5 de Vltor y el RE5F de FCD. Ten en cuenta: no todos los stocks colapsarán completamente en los RE compatibles con A5.
Para más información sobre las diferencias entre RE-A5, RE5F y RE10/A5SR, sigue este enlace: Diferencias entre REs.
El CN5F tiene como objetivo cubrir la mayor parte del área roscada de una receiver extension (RE) posible. Podría hacerse más largo, pero eso generaría problemas de compatibilidad hacia atrás con el tiempo de algunos RE al instalar el castle nut y la placa final en el RE. Hecho específicamente para el sistema Vltor A5, permitirá que incluso los stocks de carabina más largos se colapsen completamente en el RE-A5 y el RE5F de FCD. Aunque el CN5F también funcionará en RE de longitud estándar TDP, la longitud adicional del castle nut evitará que el stock de carabina se colapse completamente.
Más allá de su longitud, el CN5F comparte características comunes con su hermano menor, el CNF. El castle nut de especificación TDP es un sujetador simple y robusto que es casi perfecto para la tarea que debe realizar. A lo largo de los años, FCD ha identificado dos pequeñas quejas: primero, que las muescas de estancado parecen bastante superficiales y cortas; segundo, que a FCD no le gusta usar las muescas de la llave del castle nut como serraciones (los dedos de FCD inevitablemente encuentran estos cortes afilados) para rotarlo hacia la placa final durante la instalación.
Cambios en el CN5F
- 0.1" más largo.
- El ángulo de las muescas de estancado cambió de 45 a 30 grados, resultando en muescas más largas (25% más largas que las de especificación TDP) y más profundas que las encontradas en los castle nuts TDP.
- El número de muescas de estancado aumentó de 3 a 4, espaciadas de manera equitativa en el CNF. El castle nut debe ser estancado en dos lugares; FCD no aboga por estancar en más de dos lugares, las 4 muescas de estancado de CNF significan que, en todo momento, 3 estarán visibles y disponibles para estancar, simplemente ofrece más opciones de ubicación de estancado al usuario.
- Serraciones gruesas en el lado de la llave del nut, una característica de uso único para facilitar la rotación del CNF hacia la placa final.
Es opinión de FCD que un castle nut debe ser estancado según el TM, las muescas más largas y profundas de CNF y CN5F refuerzan la creencia de que, una vez instalado y estancado, no se aflojará sin la acción deliberada del usuario. Forward Controls Design le gusta la idea de un desmontaje rápido, pero algunas cosas en un AR están destinadas a permanecer en su lugar, y se hizo un esfuerzo considerable para garantizarlo por parte de los diseñadores originales. CNF y CN5F son una continuación y evolución en esa dirección.
El CN5F está mecanizado en billet de acero 4140 PH y nitrurado negro (también disponible en Cerakoted FDE, verde oliva y bronce quemado). Como todo lo que produce Forward Controls Design, está orgullosamente fabricado en los EE. UU.
Peso: 0.51oz
Material: 4140 PH
Fabricado en: EE. UU.