Atributos
- Acabado:
Silver
- Material:
Aluminio
- Tipo de arma:
Universal Rifles
- Peso de entrega: 0,249kg
- Altura de envío: 58mm
- Ancho de envío: 61mm
- Longitud de envío: 160mm
Silver
Aluminio
Universal Rifles
N.º de producto: 352150100
N.º fabr.: 575S
Ajustes en tres direcciones para un ajuste perfecto del arma, puntuaciones más altas y mayor comodidad al disparar. La base se monta en el arma, tu almohadilla se monta en la placa de almohadilla y el tubo roscado proporciona un ajuste total de 1-1/8" hacia adentro/fuera. Realiza giros completos o detén la rotación en cualquier lugar dentro de 360° y bloquea con los tornillos de cabeza hexagonal. La placa superior ranurada permite un ajuste vertical de 1½". Desliza un Breako Recoil Reducer en el tubo para una instalación ordenada y compacta. Combínalo con el hardware de comb ajustable de Graco para crear tu propio "Try Stock".Plazo de entrega de aproximadamente 14-21 días.
La STANDARD ADJUSTABLE BUTT PLATE de GRACO CORP es la solución perfecta para un ajuste óptimo de tu arma. Con ajustes en longitud, caída y rotación, esta placa te permitirá alcanzar puntuaciones más altas y disfrutar de una comodidad de tiro mejorada.
Con ajustes en tres direcciones, conseguirás un ajuste perfecto para tu arma. La base se monta en el arma, tu almohadilla se monta en la placa de la almohadilla y el tubo roscado proporciona un total de 1-1/8" de ajuste en/out. Puedes hacer giros completos o detener la rotación en cualquier lugar de 360° y bloquearla con los tornillos de cabeza hexagonal. La placa superior ranurada permite un ajuste vertical de 1½".
Desliza un Breako Recoil Reducer en el tubo para una instalación compacta y ordenada. Combínalo con el hardware de culata ajustable de Graco para crear tu propio "Try Stock".
Silver
Aluminio
Universal Rifles
Boyd's SS Evolution 10/22 stock 17/08/2016
I wanted to make the Boyd's ss Evolution stock fit me better. I use it for sage rats and after a day of shooting my neck would start hurting. This adjusts down about 3/4" and twists out out which was perfect to raise the comb of the stock and fit my shoulder. A few mods were needed like drilling holes. I have not shaped it to the stock yet. However, once I do I will duracoat it to match the receiver. I would buy another once I fit this one.
Just right 20/07/2015
I mounted this plate on an old single-barrel Winchester 101 Trap that I recently purchased. Stock had been cut so far back to the point it was midway in the slope of the Monte Carlo. It had also been cut at such a "custom" angle that spacers and a thick pad would not have allowed for a proper fit. The gun was absolutely useless for me although I knew that going in.
I installed one of these along with a T550 Pachmayr Trap Pad. Fitting the plates was tedious with much "cut, grind, and try" but the end result is a great fitting stock. I polished the exposed edges to a shiny finish with a sequence of filing, sanding, and rubbing with 0000 steel wool and "Mother's Aluminum Mag Polish." Due to the Monte Carlo being butchered, I had to lower the pad to what appears to be an excessive amount, but with the adjustments on this plate, I was able to get a perfect fit for me. The option of fitting the plate to the size of the recoil pad rather than fitting the recoil pad to a stock or a spacer has allowed for a greater area for recoil to occur. Might help with felt recoil.
You don't have to be a machinist or an expert gunsmith to install this plate, but basic wood and metal working skills are essential. The fitting of the plates to the stock and recoil pad and the use of a forstner bit near an existing hole takes time and patience.

Hemos encontrado un error al cargar este contenido. Actualice la página para continuar. Si el problema persiste, póngase en contacto con nuestro servicio de atención al cliente.