Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Mejora tu puntería con el montaje de mira RUGER PC CARBINE
El montaje de mira RUGER PC CARBINE VORTEX VIPER/VENOM de EGW es la solución perfecta para instalar tus miras de punto rojo de manera sencilla y efectiva. Con un diseño robusto y materiales de alta calidad, este montaje es ideal para tu rifle.
Descripción del Producto
- Material: 7075 Aluminum
- Recubrimiento: Matte Black Hardcoat
- Longitud Total: 1.811"
- Anchura Total: .99"
- Hardware de Montaje:
- (2) Tornillos de Cabeza de Botón 6-32
- (2) Tornillos de Cabeza Plana 6-32
- (1) Tornillo de Ajuste 6-32
- Ajuste de Punto Rojo: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter
Las miras de punto rojo de EGW están diseñadas para ser instaladas de izquierda a derecha (con el cañón hacia adelante). La base tiene un taper progresivo que facilita la instalación. Simplemente quita la mira trasera de tu arma y reemplázala con nuestro montaje para instalar tu Vortex Viper/Venom, Burris FastFire o Docter. No se requieren modificaciones y puedes quitar nuestro montaje y volver a colocar tu mira trasera en cualquier momento. Hardware de montaje incluido.
Instrucciones de Instalación
- Quita la mira trasera*
- Instala el montaje de mira EGW en la base
- Ajusta el tornillo de ajuste (si aplica)
- Coloca la mira de punto rojo en el montaje EGW (colocar un pequeño trozo de papel entre la mira de punto rojo y el montaje facilitará la extracción y evitará que el Loctite se adhiera a la mira de punto rojo).
- Aplica Loctite azul a los tornillos de montaje proporcionados
- Ajusta los tornillos de montaje a 15in/lbs
Nota: Los tornillos incluidos con este montaje requieren una llave allen de 5/64'' para la instalación.