Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.78" Overall Width: 1.1" Mounting Hardware: (2) 8-32 Button Head Screws, (1) 8-32 Set Screw) Red Dot Fitment: Trijicon RMR, Holosun HS507C This mount fits: Walther PPQ Classic (M1) Walther PPQ M2 (All Models) Walther PPQ 45 Walther PPQ 45 SD Walther PPQ Sub Compact Walther P99 (All Models) Walther PPX (All Models) Walther Creed Walther Creed 10 Round Walther PPS (All Models) Walther PPS M2 (All Models) This mount does not fit: Walther PPQ 22 Walther PPQ Q4 Tac Walther Q5 Match Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation.
Mejora tu puntería con el soporte para visor Trijicon RMR de WALTHER PPQ
El soporte para visor Trijicon RMR de WALTHER PPQ es la solución perfecta para quienes buscan optimizar su experiencia de disparo. Diseñado por EGW, este soporte combina durabilidad y funcionalidad.
Descripción del producto
- Material: 7075 Aluminum
- Recubrimiento: Matte Black Hardcoat
- Longitud total: 1.78"
- Ancho total: 1.1"
- Hardware de montaje: (2) Tornillos de cabeza de botón 8-32, (1) Tornillo de fijación 8-32
- Ajuste para punto rojo: Trijicon RMR, Holosun HS507C
Compatibilidad
Este soporte es compatible con:
- Walther PPQ Classic (M1)
- Walther PPQ M2 (Todos los modelos)
- Walther PPQ 45
- Walther PPQ 45 SD
- Walther PPQ Sub Compact
- Walther P99 (Todos los modelos)
- Walther PPX (Todos los modelos)
- Walther Creed
- Walther Creed 10 Round
- Walther PPS (Todos los modelos)
- Walther PPS M2 (Todos los modelos)
Este soporte no es compatible con:
- Walther PPQ 22
- Walther PPQ Q4 Tac
- Walther Q5 Match
Instrucciones de instalación
- Retira la mira trasera de tu arma.
- Instala el soporte EGW en el riel de la mira.
- Ajusta el tornillo de fijación (si aplica).
- Coloca el visor de punto rojo en el soporte EGW (colocar un pequeño trozo de papel entre el visor y el soporte facilitará la remoción y evitará que el Loctite se adhiera al visor).
- Aplica Loctite azul a los tornillos de montaje proporcionados.
- Ajusta los tornillos de montaje a 15 in/lbs.
Los tornillos incluidos en este soporte requieren una llave allen de 5/64'' para la instalación.