Flexible rubber body with spring-loaded, ABS plastic covers help seal out dirt, dust and moisture to keep the lens surfaces of your EOTech holographic sight clean, scratch-free, and ready for use in all shooting conditions. Tabs on the right and left sides of the covers allow a fast, ambidextrous flip-open action with thumb or finger pressure. Front cover opens to near horizontal position to help block rain or sunlight. Rear cover folds back on top of the EOTech’s protective hood to ensure an unobstructed view through the sight. Body section installs under the EOTech protective hood, so it’s not even visible. Noise-absorbing neoprene pads dampen the sound of the rear lens cover contacting the hood during covert operations.
SPECS: Rubber body, ABS plastic covers, neoprene pads, matte black. 1 oz. (28.4g) weight. Includes Torx wrenches for installation. XPS2/3 - 23⁄8" long, 2¼" (5.7cm) wide, 1½" (3.8cm) high. 1 oz. (28.4g) weight. Fits EOTech models XPS2 and XPS3 only.
Más...
Cuerpo de goma flexible con resorte, plástico del ABS cubre sello ayuda a suciedad, polvo y humedad para mantener las superficies de las lentes de la mira holográfica EOTech limpio, rasguñar-libre y listo para su uso en todas las condiciones de disparos. Las lengüetas en los lados derecho e izquierdos de las cubiertas permiten un rápido, ambidiestro acción flip-abierto con presión del pulgar o el dedo. Portada se abre cerca de la posición horizontal ayuda bloque lluvia o luz solar. Parte posterior cubierta pliegues detrás sobre la campana protectora de EOTech para asegurar una vista sin obstáculos a través de la vista. Sección del cuerpo se instala debajo de la campana protectora de EOTech, por lo que no es aun visible. Almohadillas de neopreno insonorizante para amortiguar el sonido de la tapa del objetivo posterior en contacto con la campana durante las operaciones encubiertas.
Especificaciones: cuerpo de goma, tapas de plástico ABS, almohadillas de neopreno, negro mate. 1 onza (28.4 g) de peso. Incluye llaves de Torx para la instalación. XPS2/3 - 23 ⁄ 8" de largo, 2¼" (5.7 cm) de ancho, 1½"(3.8 cm) de alto. 1 onza (28.4 g) de peso. Cabe EOTech XPS2 y XPS3 sólo modelos.
Más...
Evaluaciones de clientes para GG&G, INC. GG&G XPS2 & XPS3 LENS COVERS
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3
Poor Fit(04/12/2012)
Ordered this with my new Eotech. It did not fit through you could see it was designed for the sight. Instead of sending it back, I cut four slits with a fingernail clipper (one fore and aft on each side) in in bottom of the thing and ripped this initial cut up about 2/3 the depth of the side rubber. This gave the unit the flex to fit, although I have to use a rubber band around it to hold the front flap down. Poor fit to say the least. Wish there was an alternative.
For "XPS" NOT "EXPS"(02/04/2013)
Do not order this model if you have the EXPS model Eotech, it will not fit and is made strictly for the XPS models. I ordered one and found this out the hard way but Brownells gladly accepted it as a return and GG&G squared me away on which model I needed (EXPS Scope & Lense Cover Combo #GGG-1424)I gave this 5 stars because of its quality and the GG&G and Brownells customer service.
N.º de producto: 336000038 GG&G, INC. GG&G XPS2 & XPS3 LENS COVERS Ref Fabricante: GGG1272813157001888 Cuerpo de goma flexible con resorte, plástico del ABS cubre sello ayuda a suciedad, polvo y humedad para mantener las superficies de las lentes de la mira holográfica EOTech limpio, rasguñar-libre y listo para su uso en todas las condiciones de disparos. Las lengüetas en los lados derecho e izquierdos de las cubiertas permiten un rápido, ambidiestro acción flip-abierto con presión del pulgar o el dedo. Portada se abre cerca de la posición horizontal ayuda bloque lluvia o luz solar. Parte posterior cubierta pliegues detrás sobre la campana protectora de EOTech para asegurar una vista sin obstáculos a través de la vista. Sección del cuerpo se instala debajo de la campana protectora de EOTech, por lo que no es aun visible. Almohadillas de neopreno insonorizante para amortiguar el sonido de la tapa del objetivo posterior en contacto con la campana durante las operaciones encubiertas.
Flexible rubber body with spring-loaded, ABS plastic covers help seal out dirt, dust and moisture to keep the lens surfaces of your EOTech holographic sight clean, scratch-free, and ready for use in all shooting conditions. Tabs on the right and left sides of the covers allow a fast, ambidextrous flip-open action with thumb or finger pressure. Front cover opens to near horizontal position to help block rain or sunlight. Rear cover folds back on top of the EOTech’s protective hood to ensure an unobstructed view through the sight. Body section installs under the EOTech protective hood, so it’s not even visible. Noise-absorbing neoprene pads dampen the sound of the rear lens cover contacting the hood during covert operations.
SPECS: Rubber body, ABS plastic covers, neoprene pads, matte black. 1 oz. (28.4g) weight. Includes Torx wrenches for installation. XPS2/3 - 23⁄8" long, 2¼" (5.7cm) wide, 1½" (3.8cm) high. 1 oz. (28.4g) weight. Fits EOTech models XPS2 and XPS3 only.
Más...
Cuerpo de goma flexible con resorte, plástico del ABS cubre sello ayuda a suciedad, polvo y humedad para mantener las superficies de las lentes de la mira holográfica EOTech limpio, rasguñar-libre y listo para su uso en todas las condiciones de disparos. Las lengüetas en los lados derecho e izquierdos de las cubiertas permiten un rápido, ambidiestro acción flip-abierto con presión del pulgar o el dedo. Portada se abre cerca de la posición horizontal ayuda bloque lluvia o luz solar. Parte posterior cubierta pliegues detrás sobre la campana protectora de EOTech para asegurar una vista sin obstáculos a través de la vista. Sección del cuerpo se instala debajo de la campana protectora de EOTech, por lo que no es aun visible. Almohadillas de neopreno insonorizante para amortiguar el sonido de la tapa del objetivo posterior en contacto con la campana durante las operaciones encubiertas.
Especificaciones: cuerpo de goma, tapas de plástico ABS, almohadillas de neopreno, negro mate. 1 onza (28.4 g) de peso. Incluye llaves de Torx para la instalación. XPS2/3 - 23 ⁄ 8" de largo, 2¼" (5.7 cm) de ancho, 1½"(3.8 cm) de alto. 1 onza (28.4 g) de peso. Cabe EOTech XPS2 y XPS3 sólo modelos.
Más...
Evaluaciones de clientes para GG&G, INC. GG&G XPS2 & XPS3 LENS COVERS
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 3
Poor Fit(04/12/2012)
Ordered this with my new Eotech. It did not fit through you could see it was designed for the sight. Instead of sending it back, I cut four slits with a fingernail clipper (one fore and aft on each side) in in bottom of the thing and ripped this initial cut up about 2/3 the depth of the side rubber. This gave the unit the flex to fit, although I have to use a rubber band around it to hold the front flap down. Poor fit to say the least. Wish there was an alternative.
For "XPS" NOT "EXPS"(02/04/2013)
Do not order this model if you have the EXPS model Eotech, it will not fit and is made strictly for the XPS models. I ordered one and found this out the hard way but Brownells gladly accepted it as a return and GG&G squared me away on which model I needed (EXPS Scope & Lense Cover Combo #GGG-1424)I gave this 5 stars because of its quality and the GG&G and Brownells customer service.
Todos los productos de nuestra web estan en el almacen de Brownells USA, dependiendo del dia de la semana que haga el pedido este puede tardar en llegar entre 15 y 20 dias, nosotros nos encargamos de traer estos productos desde USA y de toda la documentación necesaria para la importacion (transportes, Dua, licencias de importacion y todo el papeleo necesario) los precios llevan incluido los gastos de transporte, aduanas y demas gastos que puedan generar los envios, solamente se les cobrara los gastos de envio desde nuestro almacen a su domicilio.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.